Tips for Finding Brake Controller Install Port on a 2015 Ram

Question

Question:

I have a p3 controller n the 3024 adapter, I cant find the factory end under the dash! Could it be behind the left kick panel?

asked by: Joe L

1

Helpful Expert Reply:

You do have a port for connecting the plug-in adapter for a brake controller under your dash. This is typically found under the dash to the left of the console. The attached photos shows the connector and where it should be.

It could be really buried under the dash though. Get a good flashlight and start digging through the wires under the dash since sometimes it can be somewhat out of reach.

expert reply by: Jameson C

1

click to enlarge

Answer 1

Even if you don't have the factory brake controller installed on your 2017 Ram 1500 you shouldn't need to get it flashed to activate the controller. All you would need is the Prodigy P2 #90885 and the wiring adapter #3024-P that you saw in…

view full answer...

Answer 2

The adapter needed to install your P2 brake controller #90885 in your 2015 Ram 1500 is the part #3024-P. This would not be the same as what you have for your 2010 Ram so you would need to go with the #3024-P.

view full answer...

Answer 3

As long as it's not in the way for your daily vehicle use you will be just fine to leave your Primus IQ brake controller part #TK90160 installed all the time as that is what nearly everyone does with their controllers. Now if the controller is…

view full answer...

Answer 4

Since you have a 89 degree nose on your trailer you would not need the Sidewinder pin box that your trailer has to allow you to make sharp turns. However, what you described is not something that would be normally caused by a Sidewinder. I would hate…

view full answer...

Answer 5

The 2015 Ram uses harness #3024-P for the P2 brake controller #90885. The 2-plug harness was for previous models and is not a fit for the 2015. It is the white connector that you have described up under the dash.

view full answer...

Answer 6

There are times when it is tough to locate the brake controller plug under the dash. On the 2015 Ram the factory plug is located between the brake pedal and the emergency brake pedal as shown in the attached photo. It is probably behind another…

view full answer...

Answer 7

The correct brake controller install harness to use on your 2015 Ram Sport 1500 is the #3024-P if you plan to use a Tekonsha brake controller. For a brake controller I would recommend the Prodigy P2 Brake Controller part #90885. This is our best…

view full answer...

Answer 8

Your dealer should be able to provide the details you're looking for based on the VIN. I'd agree, since that fuse is installed, you very likely have the factory 7-way tow package. Although most 1997 Dodge Ram trucks will have the connector…

view full answer...

Answer 9

Hey James, Here are the parts you need to completely redo the wiring on your 2004 Dodge Ram: - Curt Powered Tail Light Converter w/ 4-Way Flat #C59496 - Universal Installation Kit #ETBC7 The Curt kit gives you the basic light functions while the…

view full answer...

Answer 10

For your 2015 Ram 1500, I recommend the Tekonsha Prodigy P3 #90195. This is a proportional brake controller, so it will apply the brakes on your trailer at the same time you apply the brakes in your truck and with the same intensity. This controller…

view full answer...

Answer 11

As long as the Tekonsha Primus IQ Trailer Brake Controller #TK90160 that you referenced is set up correctly the braking setting will largely be based on the brakes of the trailer. When I say installed correctly I mean that you have the controller…

view full answer...

Answer 12

Hello Johnny. I am going to give you 2 options for your 2018 Ram 4x4. First option is our most cost effective proportional brake controller, the Tekonsha Primus IQ Trailer Brake Controller w/ Custom Harness - 1 to 3 Axles - Proportional #TK37ER. This…

view full answer...

Tips for Finding Brake Controller Install Port on a 2015 Ram

Continue Researching