What Size Bolts are Needed to Install Curt Hitch in a 2006 Toyota Sienna

Question

Question:

What size of bolts do I need to install the trailer hitch to the vehicle?

asked by: Gary

0

Expert Reply:

The Curt trailer hitch part # C13105 comes with all of the install hardware needed, but the bolts are size M12-1.25x40 hex.

If you need the replacement hardware you would want part # RHK. If you enter the part number on this product page we will ship you out the correct hardware.

expert reply by: Jameson C

0

Answer 1

In all likelihood you will not have to tap the holes on your 2006 Toyota Sienna to get the hitch bolts to fit. Usually the issue is that the weld nuts on the vehicle will get packed with grime and corrosion and all you will have to do is clean them…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

Hey Claudia, I checked with Curt just now and confirmed that their hitch part #C64DR does fit all models of the 2026 Toyota Corolla Cross which includes the hybrid models so it would work great for you. We also had customers with similar hybrid…

view full answer...

Answer 10

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 11

Good morning to you as well Steve, and congrats on your new van! I would be more than happy to make a recommendation for you! The best hitch for your 2026 Toyota Sienna, is going to be our etrailer item #e56RR. This is a class III hitch with a…

view full answer...

Answer 12

Hey Michael, congrats on the new SUV. The EcoHitch item #EH87CR does not require you to remove the rear bumper assembly when installing. It does require some slight fascia trimming though. You'll have to remove a 2-3/4” deep and 4-1/2” wide…

view full answer...

What Size Bolts are Needed to Install Curt Hitch in a 2006 Toyota Sienna

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching