Distance From Mounting Flange of Bulldog Jack BD155157 to Bottom of Outer Tube

Question

Question:

How long is the length of the outer tube from the bottom of the three hole flange to bottom end of the outer tube?

asked by: Dave

1

Helpful Expert Reply:

The distance from the bottom of the mounting flange of the Bulldog Jack part # BD155157 to the bottom of the outer tube of the jack measures 6-1/4 inches.

expert reply by: Jameson C

1

click to enlarge

Answer 1

You have to be careful using both a slider and an offset because that creates extra stress on the trailer frame and hitch. Another thing to look at is if the 5th wheel hitch you use can be used with an adapter. On some, you can't. Another option…

view full answer...

Answer 2

You are correct, gooseneck trailer to 5th wheel hitch adapter #BD0289640300 is an inner tube only that fits inside the outer tube of the gooseneck coupler. The tube is not solid, it is hollow, and the inner diameter is approximately 3-1/2 inches.

view full answer...

Answer 3

The king pin on the Bulldog Gooseneck-to-5th-Wheel Coupler Adapter, #BD0289640300, is the standard 2 inch king pin that is used on all recreational and commercial fifth wheel trailers. We do not sell any gooseneck-to-fifth-wheel adapters with…

view full answer...

Answer 4

The 155 is a series of jacks and not just one jack. It sounds like you might have something more like #BD155022 which has more of the outer tube below the mounting flange. There is also a version with a zinc finish #BD155028.

view full answer...

Answer 5

While I don't know exactly what landing gear you have on your 2011 Keystone Raptor 3812 Toy Hauler, I can say that you should be able to replace them with the Landing Gear Set w/ Handle #RVLG-8HDL as this landing gear uses the standard weld mount…

view full answer...

Answer 6

Aside from the weight capacity of the jacks and their speed, they also have different mounting bracket locations. If you don't mind potentially having someone do some cutting and welding on your trailer then either one will work great for you. If…

view full answer...

Answer 7

For a trailer brake controller, I recommend the Tekonsha Prodigy P3 Trailer Brake Controller, #90195 with the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers, #3070-P which is completely plug-in-play. The Tekonsha P3, #90195 is the…

view full answer...

Answer 8

Most likely you need to go with the Reese Landing Gear Set #RP500708 because it has the typical inside to inside and outside to outside spacing of 15-1/2" and 17-1/2" respectively. This is the most common weld stop measurements which is why…

view full answer...

Answer 9

The connector for the Tekonsha Plug-In Wiring Adapter #3070-P can be difficult to locate under the dash on your 2021 Honda Ridgeline. You will need to follow the wiring for the connector that I included in the image below as this will lead you to the…

view full answer...

Answer 10

The factory brake controller connector under the dash is not all that visible but it is fairly easy to locate. It is a 4-pin connector that is located underneath and left of the steering column. It will be taped to another harness near the brake…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Distance From Mounting Flange of Bulldog Jack BD155157 to Bottom of Outer Tube

Featured Help Information

Miscellaneous Media

Continue Researching