Recommendation for Trailer Wiring a 2004 Mitsubishi Fuso FE

Question

Question:

Hi , do you carry T wire trailer conector for truck mitsubishi fuso fe-sp 2004..

asked by: Edgar F

0

Expert Reply:

I have a wiring solution for you, but there is no custom T-harness for your 2004 Mitsubishi-Fuso FE. The Tekonsha ZCI Circuit Protected Vehicle Wiring Harness # 119250KIT is the best solution for a universal harness for your truck. This kit uses a powered converter with circuit protection to safeguard your vehicle and the module. It also includes everything necessary to hardwire it to your vehicle and connects without splicing into your current wiring. Be sure to use the included tester to make sure you have the correct wires before splicing. The colors on the trailer harness are as follows below.

Green = right turn
Brown = tail lights
Red = brake light
Yellow = left turn
White = ground
Black = 12 volt battery lead

expert reply by: Jackie C

0

Answer 1

On your 2004 Mitsubishi FUSO FE-145, You will need to find a 12-volt signal of the brake light wiring when installing a brake controller. The best location would be to tap into the brake light wiring anywhere after the lighting control module. This…

view full answer...

Answer 2

There should not be 12 volts coming out of your ground terminal (7:00) on your vehicle connector. That sounds like where your problem is located. It sounds as if the 12 volt accessory that should be in the 2:00 position of your connector has been…

view full answer...

Answer 3

Hi Austin; it sounds like you want to install a new 7-way to completely bypass the factory wiring. You can use the Universal Wiring Harness w/ ModuLite and Brake Controller Harness #22551 you were looking at to accomplish this. As the name implies,…

view full answer...

Answer 4

Yes, dielectric grease like the Dielectric Grease for Electrical Connectors #11755 can and should absolutely be used on electrical connectors like your 4-pin trailer connector. Dielectric grease does a great job of protecting your equipment from…

view full answer...

Answer 5

The 2017 Mitsubishi Fuso Canter FE130 is not a vehicle that we have had much experience in dealing with unfortunately so I don't have any information as to whether or not it came pre-wired with a trailer brake controller but the dealer might. The…

view full answer...

Answer 6

For your 12V wiring to your 7-way, we have people running many different things off that 12V wire. 12 gauge or even better 10 gauge ensures that the power is transferred timely and accurately. We have a kit for brake controllers and 12V wiring for…

view full answer...

Answer 7

Normally you can find the brake light switch under the dashboard at the top of the brake pedal. There could be a number of wires attached to the switch so you can use a tester like part #PTW2993 to test the wires. Since the auto manufacturers can use…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Recommendation for Trailer Wiring a 2004 Mitsubishi Fuso FE

Featured Help Information

Miscellaneous Media

Continue Researching