Availability of a Replacement Castle Nut for Trailer Spindle

Question

Question:

I NEED THE 2 AXLE NUTS AND WASHERS FOR A 1972 SCOTTIE CAMPER.IVE REPLACED THE BEARINGS.CAN YOU HELP ME? THANKS

asked by: EDDIE C

0

Expert Reply:

We have a few options that could work for you, but you will need to measure the threads of your spindle to determine which would work.

For a 1 inch spindle nut you would need the part # 165686, for a 7/8 inch nut you would need part # 165931. These are the two most popular sizes.

expert reply by: Jameson C

0

Answer 1

From what I was able to find out from my research, the Tie Down Engineering 11033 hub has a 5 on 4-1/2" bolt pattern and is designed for 3500-lb axles. Replacement hubs that have these specs typically use a #L68149 inner bearing and #L44649…

view full answer...

Answer 2

That is most likely a Tie Down hub which while we don't carry that exact brand we most likely have what you need. Since the stud and bearings need replacing it might make more sense just to replace the hub since idler hubs like what you have are…

view full answer...

Answer 3

I believe we can narrow this down based on the information you are referencing. However, the best way to be sure is to measure your existing bearings or spindle with a digital caliper like the #PTW80157. It looks like one bearing is stamped with…

view full answer...

Answer 4

According to my research, your trailer will have a 3500 lb axle on it. The replacement for your TDE 11033 hubs should be #AKIHUB-545-35-G-EZ-K, which use an L68149 inner and an L44649 outer wheel bearing along with a 58846 grease seal that has a…

view full answer...

Answer 5

The 11033L hub shown in your photo was manufactured by Tie Down Engineering, or TDE. What you have there is a hub for a standard 3500 lb axle which has a 5 on 4-1/2 inch bolt pattern. For an idler hub, I'd recommend the galvanized…

view full answer...

Answer 6

While we cannot confirm for sure what the "L" means on the 11033L, the "L" does not make a differences when coming to fitment of the hub. With that being said, the Tie Down Engineering 11033 hub has a 5 on 4-1/2" bolt pattern…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Availability of a Replacement Castle Nut for Trailer Spindle

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching