What is Diameter Of Mounting Pipe on Pro Series Round Pipe-Mount Swivel Jack # PS1401460303
Updated 09/08/2015 | Published 09/05/2015
Question:
I Have an A-Frame 16 ft. flat bed trailer. The jack is old and froze and cant turn down. Tried to lube it cant come apart. better off buying one that will fit it. So far, this model noted above is the closest to the one I have. The only question I have is will the sleeve welded on the jack slip onto/over the sleeve already welded on my trailers A-frame. Thus, I need to know the diameter size of the opening of the one on your jack. Dont know if these things are all standard openings. Hate to order it and find it wont slip over the short one already on my A-Frame. I had an Omni 5,000 ton one just like yours on it. Im attaching a couple of pictures of it. Youll be able to see the one attached to the A-frame of the trailer is smaller in diameter than the one welded on the jack stand.
asked by: Larry P
Expert Reply:
The Pro Series Round Pipe-Mount Swivel Jack # PS1401460303 includes a weld-on steel tube that measures 2-inches in diameter. This tube, or the one already on your trailer, accepts the larger mating tube on the jack itself and is secured with the included pin. These jack fittings are standardized and you'll have no trouble installing the new jack on the old pipe mount.
Product Page this Question was Asked From
Pro Series Round, Pipe-Mount Swivel Jack w/ Footplate - Topwind - 10" Lift - 5,000 lbs
- Trailer Jack
- Car Hauler
- Enclosed Trailer
- Utility Trailer
- Side-Mount Jacks
- Swivel Jacks
- Standard Grade
- 4001 - 5000 lbs
- Manual Jack
- 10 Inch Lift
- Weld-On
- With Rectangle Foot
- Pro Series
more information >
Continue Researching
- Article: Trailer Lighting Requirements
- Shop: Pro Series Round, Pipe-Mount Swivel Jack w/ Footplate - Topwind - 10" Lift - 5,000 lbs
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: Where Do the Wires on the Universal Install Kit for Trailer Brake Controllers Get Installed?
- Search Results: tekonsha prodigy p3
- Search Results: jack
- Video: In-Depth Review of the Deka Jacketed 2 Wire, 10 Gauge, Brake Wire
- Video: An In-Depth Look at the Quick Splices
- Search Results: tekonsha prodigy p2
- Search Results: brake wire
- Search Results: 10 gauge wire
- Shop: etrailer Bolt-On Swivel Mounting Plate for 3,500-lb Trailer Jacks with a 5/8" Swivel Pin
- Shop: Round, Pipe Mount Swivel Jack w/ Footplate - Weld On - Zinc - Topwind - 10-3/4" Travel - 2K
- Q&A: Replacement Trailer Jack for 2001 Viking Saga 1906 Pop-Up Camping Trailer
- Video: Choosing the Right Swaybar Upgrades
- Q&A: Replacement Pipe Mount Recommendation for Round, Pipe Mount Swivel Jack # TJP-2001-B
- Q&A: Replacement Pipe Mount to Use with Pro Series Jack # PS1401080303
- Search Results: curt trailer hitch ball
- Shop: etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector
- Video: Lock N Roll Articulating Coupler Review
- Shop: Optronics Fleet LED Trailer Tail Lights w/ Grommets - Stop,Turn,Tail - Submersible - Oval - Qty 2
- Shop: Fusion LED Trailer Tail Light - Stop, Tail, Turn, Backup - Submersible - Oval - Red/Clear Lens
- Shop: Fulton Drop-Leg Stabilizer Jack with Mounting Channel - Weld-On - 28" Leg - 13" Bracket -
- Search Results: trailer wiring
- Video: An In-Depth Look at the Pro Series Round, Pipe-Mount Swivel Jack w/ Footplate
- Q&A: Recommended Support Jacks for Rear of Tandem Axle Dump Trailer
- Q&A: Recommended Stabilizer Supports For Equipment Trailer That Lifts Back Of Truck Off The Ground
- Video: Ultimate Overview of the Fulton Drop-Leg Stabilizer Jack with Mounting Channel
- Q&A: Recommended Replacement Wheel Stud For a 2016 Kaufman 3 Car Wedge Trailer With 7,000 lb Axle
- Article: Trailer Couplers
on Trailer Jack
