Which Lights will Illuminate on the Tester # I26 When Brakes are Applied

Question

Question:

so what led should light when yhe brake light is activated?

asked by: Packy

1

Helpful Expert Reply:

When your brake lights are pressed and you are using the # I26 as a tester the two pins opposite of the jacketed (ground) pin will illuminate. These are the left and right turn/brake light circuits.

expert reply by: Jameson C

1

click to enlarge

Answer 1

That is a great question. The good news is that consumers are protected by the Federal Magnuson-Moss Warranty Act. This act essentially states that if something were to break or go wrong on your Jeep and you take it in for warranty repair, the dealer…

view full answer...

Answer 2

If you are putting a test light like the Curt #I26 on your vehicle-side 4-Way then you may have installed your vehicle-side 4-Way incorrectly. Is your running light indicator blinking when you put your right turn signal on? If this is the case then…

view full answer...

Answer 3

From left to right the first light tests running lights, the middle light tests left turn and brake lights, and the last light tests right turn and brake lights. On a 4-Way flat vehicle connector, the one exposed pin is the ground, next to that is…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

Hello Ken, congrats on the new van! We do have the hitch and wiring you need for your 2025 Toyota Sienna. Here is what I recommend: - Curt Trailer Hitch Receiver - Custom Fit - Class III - 2" #C22UR - Curt T-Connector Vehicle Wiring Harness with…

view full answer...

Answer 7

The ideal height will actually have to do with how tall the coupler of the trailer is from the ground. The Draw-Tite #76020 will sit at 13 1/2 inches from the ground to the top of the hitch when installed on a 2016 Mazda CX-9. From what I could find…

view full answer...

Answer 8

Hey Jean! We do have a hitch for your 2025 Subaru Crosstrek. The best one is the etrailer Hitch #e98912. This is a Class III hitch with a bolt-on installation. It also features a unique matte black finish which blends in well with OEM trim and helps…

view full answer...

Answer 9

Hi Billy; the inside dimensions of the 24x60 Curt Cargo Carrier #C18152 are 60" long x 24" wide x 5-1/2" deep. Based on this you can use the Buyers Products Utility Storage Box #3371712250. This storage box is 51" long x…

view full answer...

Answer 10

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 11

The Curt #C12241 is rated to tow up to 3500-lbs, but when towing you're always going to be limited to the lowest rated component in your towing setup. From what I'm able to tell by researching, the 2018 Hyundai Tucson only has a towing…

view full answer...

Answer 12

When we research towing capacities we base it off of what the owner's manual says but for some unknown reason there are no online manuals available for a 2018 Hyundai Tucson. I did take a look at the Hyundai website and as you said it listed the…

view full answer...

Which Lights will Illuminate on the Tester # I26 When Brakes are Applied

Product Page this Question was Asked From

Continue Researching