Should Landing Gear Drop Legs be Lowered First Before Using Motor to Level 5th Wheel Trailer
Updated 08/17/2015 | Published 08/16/2015 >
Question:
When first dismountingthe truck should the front pin jacks be lowered so that the the jacks hit the ground at the same time
asked by: Doig
Expert Reply:
Before uncoupling a 5th wheel trailer from the truck you will need to have the jacks in position so that they are supporting the weight of the trailer. You may or may not have to use the drop legs on the jacks in a system like # LC358590 but doing so will reduce the amount of travel the jacks have to go thus reducing the amount of time it takes to get all the jacks into place.
What I would do is lower the jacks a little first using the motors and then use the drop legs to make contact with the ground. This will allow a little wiggle room should you need it. Otherwise you would not be able to power the legs up should you need to because the inner tube will already be retracted as far as it will go.
Product Page this Question was Asked From
Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System w Touchpad - 4-Point Set
- Camper Jacks
- 5th Wheel Camper
- Stabilizer Jacks
- Steel
- 10001 lbs or More
- Electric Jack
- 36 Inch Lift
- Bolt-On
- 4 Jacks
- Lippert
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Search Results: lippert~landing~gear
- Q&A: Replacement Landing Gear for a 2010 Forest River Rockwood Signature Ultra Lite 5th Wheel
- Shop: Landing Gear Set w/ Handle - 36-1/2" Lift - 8,000 lbs
- Q&A: Replacement Landing Gear Motor, Gear Box and Switch for Model 1A065012-02-01
- Shop: Trailer Wiring
- Video: Comprehensive Review: Replacement Follow Leg for Stromberg Carlson Landing Gear
- Video: Feature Review Replacement Follow Leg for Stromberg Carlson Landing Gear
- Shop: Replacement Lead Leg for Venture 5th Wheel RV Landing Gear
- Shop: Lippert Components Tuson High Speed 5th Wheel RV Landing Gear Motor
- Shop: Replacement Motor for Stromberg Carlson Electric Landing Gear - 5,500 lbs
- Shop: Landing Gear Set - 36-1/2" Lift - 8,000 lbs
- Shop: Buyers Products Circuit Breaker w Manual Push-to-Trip Reset - Surface Mount - 30 Amp
- Shop: Lippert HD 6500-lbTuson 5th Wheel RV Landing Gear Motor
- Q&A: Venture Landing Gear is Blowing Fuses
- Q&A: Tips for Removing Lower Roll Pin to Repair Stromberg Carlson Landing Gear
- Q&A: Recommended Landing Gear Set for 2007 Rockwood Signature Ultralight
- Q&A: Replacement Motor for a 125340 Motor Model Number 1a065012-02-01
- Q&A: Is there a Way to Identify 5th Wheel Trailer Landing Gear with No Markings
- Article: Trailer Wiring Diagrams
- Video: Firestone Ride-Rite Air Bags with Easy Mount Compressor Feature Breakdown
- Search Results: trailer hitch
- Shop: Trailer Hitch
- Search Results: trailer wiring
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Search Results: trailer jack
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Shop: Suspension Enhancement
- Video: B&W Companion OEM 5th Wheel Hitch Manufacturer Breakdown
- Video: Curt T-Connector Vehicle Wiring Harness Review C56040
- Article: How to Measure for Trailer Hitch Drop


