Trailer Vent Recommendation for Venting an Air Conditioner Unit

Question

Question:

I am looking to vent a portable air conditioner outside of my cargo trailer/camper. any suggestions? I was thinking of the half moon polypropylene vents.

asked by: Randy S

0

Expert Reply:

The 2-Piece Polypropylene Trailer Vent # HMAV2-AVT2 would work well as an air conditioner vent on your trailer. You would just need to cut a 3 inch hole in your trailer to install the vent.

For self-tapping screws the part # 31071 would work great and then for sealant part # 0160297.

expert reply by: Jameson C

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 3

You can use the RV Propane Gas Detector #RS64FR (white) or #RS44FR (black) to replace your current Atwood 31013 propane gas detector. This will also use a 12v, 2-wire installation like your current detector.

view full answer...

Answer 4

Hello Sam; that is a great question! I reached out to Furrion and you will be able to use the Furrion Chill Cube #FR69TD (white) or #FR49TD (black) with your furnace. However, the remote is not capable of operating the furnace at this time. Also, we…

view full answer...

Answer 5

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 6

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 7

Hey Jon; I was actually just talking to Furrion about heat options for the Chill Cube yesterday (1/21/2025). At this time, the only way to have heat with this unit is through a furnace on a ducted setup. The Furrion Chill Cube RV AC w/ Air…

view full answer...

Answer 8

Both the Roadmaster and Blue Ox tow bars are great options. But if it was my decision to make I would go with the Blue Ox Avail part #BX7420 as we have found that the Blue Ox tow bars are a little easier to connect and disconnect from. Also this tow…

view full answer...

Answer 9

To install a Redarc Tow Pro Liberty in your 2023 Toyota Tacoma Sport you will need the following parts: Redarc Tow-Pro Liberty Brake Controller item #RED24FR Plug-and-Play Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers item #RED99FR…

view full answer...

Answer 10

Hey Dan, we actually have a few install videos for hitches on a 2023 Subaru Outback Wagon but most of them are for the Curt hitch part #C67JR or the etrailer part #e25TR. I attached install videos down below on this page for both for you to check…

view full answer...

Answer 11

Hey Bob, you are definitely thinking in the right direction adding rear support with that much constant weight back there. Between the 320 lbs you’re carrying full time, another 200 lbs with the kayaks, and up to 500 lbs of tongue weight, you’re…

view full answer...

Answer 12

Hello Mark, thanks for reaching out. Both the hitches you mentioned, the Draw-Tite #DT73RR and the Blue Ox #BLU92UR are a confirmed fit for the 2024 Subaru Outback. Both hitches also use the same size spacer and may require enlargement of the access…

view full answer...