Brake Controller Wiring Harness for a 2015 Ram 1500 and P2 Brake Controller

Question

Question:

im a little confused,i thought the 2015 ram used 2 wire hook up thats wraped in foam beside the gas peddle..but i do see the single white plug also.im thinking the 2 plugs are for the factory system and the 1 white plug for after market..i already have the p-3 from my 07 ram and love it.so if i get the 3024-p i can use it in my 2015 ram?

asked by: Mark W

0

Expert Reply:

The 2015 Ram uses harness # 3024-P for the P2 brake controller # 90885. The 2-plug harness was for previous models and is not a fit for the 2015. It is the white connector that you have described up under the dash.

expert reply by: Michael H

0

Answer 1

As long as it's not in the way for your daily vehicle use you will be just fine to leave your Primus IQ brake controller part #TK90160 installed all the time as that is what nearly everyone does with their controllers. Now if the controller is…

view full answer...

Answer 2

Your dealer should be able to provide the details you're looking for based on the VIN. I'd agree, since that fuse is installed, you very likely have the factory 7-way tow package. Although most 1997 Dodge Ram trucks will have the connector…

view full answer...

Answer 3

You'll need a new harness part #3024-P to go along with the Tekonsha Primus IQ part #TK90160 as there was a big enough change in 2015 for the Rams that they had to come up with a new fit for it.

view full answer...

Answer 4

For your 2015 Ram 1500, I recommend the Tekonsha Prodigy P3 #90195. This is a proportional brake controller, so it will apply the brakes on your trailer at the same time you apply the brakes in your truck and with the same intensity. This controller…

view full answer...

Answer 5

There are times when it is tough to locate the brake controller plug under the dash. On the 2015 Ram the factory plug is located between the brake pedal and the emergency brake pedal as shown in the attached photo. It is probably behind another…

view full answer...

Answer 6

Hey James, Here are the parts you need to completely redo the wiring on your 2004 Dodge Ram: - Curt Powered Tail Light Converter w/ 4-Way Flat #C59496 - Universal Installation Kit #ETBC7 The Curt kit gives you the basic light functions while the…

view full answer...

Answer 7

Even if you don't have the factory brake controller installed on your 2017 Ram 1500 you shouldn't need to get it flashed to activate the controller. All you would need is the Prodigy P2 #90885 and the wiring adapter #3024-P that you saw in…

view full answer...

Answer 8

Since you have a 89 degree nose on your trailer you would not need the Sidewinder pin box that your trailer has to allow you to make sharp turns. However, what you described is not something that would be normally caused by a Sidewinder. I would hate…

view full answer...

Answer 9

The correct brake controller install harness to use on your 2015 Ram Sport 1500 is the #3024-P if you plan to use a Tekonsha brake controller. For a brake controller I would recommend the Prodigy P2 Brake Controller part #90885. This is our best…

view full answer...

Answer 10

The adapter needed to install your P2 brake controller #90885 in your 2015 Ram 1500 is the part #3024-P. This would not be the same as what you have for your 2010 Ram so you would need to go with the #3024-P.

view full answer...

Answer 11

As long as the Tekonsha Primus IQ Trailer Brake Controller #TK90160 that you referenced is set up correctly the braking setting will largely be based on the brakes of the trailer. When I say installed correctly I mean that you have the controller…

view full answer...

Answer 12

You should have a single plug under the driver side dash on your 2015 Ram 1500 that you will simply need to connect an Adapter, like part #3024-P, to for installing a Brake Controller, like the Tekonsha Prodigy P3 #90195. If you check out the…

view full answer...

Brake Controller Wiring Harness for a 2015 Ram 1500 and P2 Brake Controller

Continue Researching