How to Order the CE Smith Bunk-Style Guide-Ons without Boards

Question

Question:

My dual axle SeaStar trailer will need bunk guide-ons with sideboards 6 feet long so the uprights dont interfere with the fenders. Your kit offers 5 foot boards. I can purchase 6foot boards and carpeting locally. What is the price for 4 #27609PG uprights and the full hardware kit, omitting the boards? Trailer frame is 3inch x 4inch galvanized.

asked by: Richard M

0

Expert Reply:

You could piece together the part # CE27600 without the boards if you wanted to. For that you would need the part # CE27609PG for the uprights, # CE11452-A for the mounting brackets, and finally part # CE10206G for the swivel brackets and you would have everything but the boards and carpeting.

expert reply by: Jameson C

0

Tim

3/11/2025

I would like to know if it is possible to to use the CESmith post extensions on my present wood guides? I have a 2018 Shorelander trailer which carries my 16ft Lund fishing boat.

Jameson C.

3/11/2025

@Tim I don't see why you couldn't. You meant like take your current wood bunk guides and use them with the pieced together kit mentioned above right? They should bolt right to the bracket.

Answer 1

The vertical bunk brackets you referenced do not have a weight capacity rating. The aluminum ones item #CE10161A40 are regularly used and should be fine, but if you are concerned about the strength then you can stick to the galvanized steel ones,…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 6

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 7

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 8

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 9

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 10

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Answer 11

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 12

Hey Kelvin, welcome back. To flat tow a 2026 Ford Maverick with your Demco Commander II Tow Bar item #DM9511012, I recommend the following parts: Baseplate Kit - Demco Tabless Base Plate Kit item #DM38CV Wiring Harness - Roadmaster Diode 7-Wire to…

view full answer...

How to Order the CE Smith Bunk-Style Guide-Ons without Boards

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching