Fulton 1500-lb Bolt-Thru Pull-Pin Swivel Jack

Question

Question:

I am replacing a fulton magnum series trailer jack 1200 lb. the mounting plate bolt pattern is 3inch tall By 5inch 1/2 wide. Will this Fulton XLT bolt thru bolt up to my existing welded brackets.Im wanting to purchase 1500 lb trailer jack. Thank You.

asked by: Russell L

0

Expert Reply:

Thank you for the photo of your Fulton jack.

Your jack is a bolt-thru type pull-pin swivel jack. The 1500-lb-rated Fulton jack you can use in place of your existing one is part # FXP15L.

expert reply by: Adam R

0

click to enlarge

Answer 1

Without knowing the part number and manufacturer of your current trailer jack, I couldn't speak to the compatibility of the mounting plate for your current jack with the mount that the Fulton #F141132 XLT uses. The #P9012-00 weld-on mount for the…

view full answer...

Answer 2

I do have options for you but we do not offer any jacks that will fit the existing bracket you have on your trailer frame. Therefore, I recommend just using the Fulton Bolt-Thru Swivel Marine Jack part #FXP15L as it is a bolt-on fit that won't…

view full answer...

Answer 3

The plunger must be larger than the opening on the socket in order to hold it in place. With the Pivoting Door Holder Receiver #37210635 having an opening slightly over 1/2" and your current socket measuring slightly under a 1/2", I would…

view full answer...

Answer 4

The Fulton XLT Swivel Trailer Jack #F141133 that you referenced comes ready to be installed and used. It would not require any greasing prior to initial use.

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Fulton 1500-lb Bolt-Thru Pull-Pin Swivel Jack

Continue Researching