Adding 7-Way Trailer Connector to 2008 Honda Ridgeline

Question

Question:

Will HM40975 work for a 2008 Honda Ridgeline ? Just plug and play ? Will the 7 pin receiver I have just plug into the back of this?

asked by: Dana K

0

Expert Reply:

If your 2008 Honda Ridgeline came with a factory installed 7-Way trailer connector it is possible that # HM40975 will fit. You need to look at the wiring harness that plugs into the back of the factory 7-Way. If it looks the same as the back of # HM40975, see picture, then you can use it.

If your Ridgeline did not come with a 7-Way then to add one you will start by installing a 4-Way (unless the truck already has one) using # 118400. Then you will need to install 4- and 7-Way installation kit # ETBC7. I have included some links that show and explain the ETBC7 installation for you.

The ETBC7 also includes wiring to install a brake controller. If you need a brake controller I recommend the P2 # 90885 because it is easy to set up, easy to use, and it is reliable.

expert reply by: Chris O

0

click to enlarge

Jerry Z.

7/11/2020

I purchased a 2008 Honda Ridgeline and I want to pull travel trailer I need a hitch and wiring I have a Brakeman controller but don’t know how to wire it the trailer weighs 4200 lbs I need help

Chris R.

7/15/2020

Starting with the trailer hitch I highly recommend the Draw-Tite # 75280. I've linked an install video on your 2008 Ridgeline below as well. Then for wiring you'll need to start with a 4-Way connector, for which the Tekonsha # 118400 will work perfectly. To install your existing Brakeman controller you will need the Wiring Kit # ETBC7, which will convert this to a fully functional 7-Way connector.

Helpful Links

tv-hitch-install-2008-honda-ridgeline.aspx

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 11

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 12

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Adding 7-Way Trailer Connector to 2008 Honda Ridgeline

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching