How to Install a Brake Controller On a 2006 Ford F-150 With 7-Way Trailer Towing Package

Question

Question:

Installing a used/working brake controller from another vehicle into 2006 F150 with trailer tow pckg. 7 prong socket-OEM. Would like to know where wires or connector is under dash to hook-up ? What to look for ? Controller has 4 wires blk-12V, red-stoplight, wht-grd, blue-trailer brakes

asked by: Tom

0

Expert Reply:

Installation of your brake controller should be very easy with the factory 7-way trailer connector on your vehicle. All you will need to complete the installation is the Universal Brake Control Wiring Adapter Ford, Land Rover, Lincoln, Mercury, item # 3035-S. You will wire the like colors on your brake controller to the plug in adapter and mount the brake controller in an accessible location your installation will be complete. You have the wiring colors and functions correct.

The connector will be located under the dash near the factory diagnostic port usually referred to as the OBD II port.

After you have everything installed you will need to set the brake controller up to work with your trailer and the new vehicles wiring. If you need instructions for your controller let me know what brand and model you have and I will be glad to try to find a copy to send you.

expert reply by: Robert G

0

Answer 1

The brake controller installation on your 2006 F150 is pretty easy. The connector for the brake controller is located under the dash, behind and to the right of the OBD port as shown in the video I've linked for you. You'll need the brake…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 7

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 8

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 9

Hey Phil, If you're looking for the factory wire harness for a plug and play connection you'll find a connector that's gray with a red/orange center like the plug on the Curt Custom Wiring Adapter for Trailer Brake Controllers #C51436.…

view full answer...

Answer 10

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 11

Hey Eric, the Weigh Safe True Tow part #WS37RR that you referenced would be your best option for a weight distribution system for your Grand Design 25G. What are you towing the Grand Design with and does it have a 2.5 inch hitch?

view full answer...

Answer 12

Hello Tim, Are you asking if you can back up with just the head installed on the Weigh Safe True Tow Weight Distribution Hitch #WS79VR, when you put the trailer coupler onto the ball? If so, then yes because at that point it is really just a ball…

view full answer...

How to Install a Brake Controller On a 2006 Ford F-150 With 7-Way Trailer Towing Package

Continue Researching