Replacement Hub Recommendation for a Dexter 8-155 Hub

Question

Question:

Will this hub replace a Dexter 8-155 4x9.44 lug hub?

asked by: Kenton W

1

Helpful Expert Reply:

Yes, we had a customer who was able to replace his Dexter 8-155 hubs with the # 8-201-5UC3-EZ that you referenced so they should work well for you.

You can verify that this hub will work for you by pulling your current hub and making sure they have inner bearing 25580 and outer bearing LM67048.

expert reply by: Jameson C

1

click to enlarge

Answer 1

Hey Mark, so we had a customer that had a Dexter 8-155 hub/drum like you have and they were able to replace it with the #8-201-5UC3-EZ so that would be what I would go with. Then for the correct brake assemblies to match this you would want the part…

view full answer...

Answer 2

If you need the 4 lug option you have then no we don't have anything that would work, but based on the #8-201-5UC3-EZ being a suitable replacement we also know the part #42865-KIT would too and it does cost less. It is an 8 on 6-1/2 inch bolt…

view full answer...

Answer 3

You will need the Grease Seals #RG06-050 for each of your 4,000LB Dexter axles. These are sold as a pair so that you can replace both seals on one of your axles so you will need 2 kits to replace all 4 seals. The Seal Puller #PTW1219 will help you…

view full answer...

Answer 4

The jack you referenced, Bulldog Heavy-Duty Rack-and-Gear Jack #BD165412, does have a removable steel wheel. My contact at Bulldog did confirm that the jack could be mounted in an inverted position (upside down) without the wheel and retain the same…

view full answer...

Answer 5

The brake assemblies you have are 7k Dexter assemblies that are 12 inch by 2 inch in size. The part number #AKEBRK-7-SA will work as a great replacement set. This includes assemblies for both sides of your trailer that are self adjusting.

view full answer...

Answer 6

It looks like the studs in your brake assembly are closer together (center to center) at the bottom. If the center to center bolt spacing matches the photo I've provided, then the #23-105-09 you'd looked at would be the correct replacement…

view full answer...

Answer 7

If the integrated brake controller on your 2008 Chevy Silverado 2500 is not recognizing when a trailer is connected, then that could indicate damage to the brake output wire or the connector on the truck itself. It could also be the trailer. To…

view full answer...

Answer 8

We don't offer a grease seal that would have the proper outer diameter to work with your Hadco Hubs, but we might have a solution that would allow you to upgrade your existing hub/drums so they're compatible with easily obtainable grease…

view full answer...

Answer 9

Yes, for a hub with a 6 on 5-1/2 inch bolt pattern that has the same bearings as the part #BK3-300 we have the hub part #8-201-5UC3-EZ from Dexter.

view full answer...

Answer 10

We've got you covered! To replace your wheel bolts you need the Dexter Wheel Bolt #7-262 which is a 1/2" diameter and 2-11/16" long. Since your hub and drum assembly looks to be pretty worn though I recommend just replacing the whole…

view full answer...

Answer 11

The Dexter Electric Trailer Brake Kit #23-105-106 are a replacement set for the 023-358-00. This kit includes a right and left brake assembly that is manually adjustable. I recommend the Dexter Nev-R-Adjust Electric Trailer Brake Kit #23-458-459 as…

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Replacement Hub Recommendation for a Dexter 8-155 Hub

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching