Replacement Zip Strip Recommendation for a Yakima RidgeBack 4 Bike Rack

Question

Question:

Will these fit the Yakima Ridgeback 2 bike rack? Thanks

asked by: Bob

0

Expert Reply:

Yes, I checked with Yakima and the Replacement Zip Strips # Y8890297 that you referenced have been confirmed to fit your Yakima Ridgeback Bike Rack part # Y02458.

expert reply by: Jameson C

0

Answer 1

You've actually found the correct part. The Replacement SuperCush Anti-Sway Cradle and ZipStrips for Yakima Hanging-Style Bike Racks #8880598 is the correct part to replace the anti-sway cradle on the Yakima Ridgeback models manufactured after…

view full answer...

Answer 2

Most Yakima hanging racks like your RidgeBack use the same hitch pin. The pin you're looking for is part #889-0231.

view full answer...

Answer 3

Hello Bob, thanks for reaching out. The Replacement ZipStrips #Y8890297 you were looking at will fit the Yakima FullSwing, RidgeBack and SwingDaddy bike racks. I am not quite sure what you mean by "sidewinder cradle for tandem", but as long…

view full answer...

Answer 4

If you look at the provided diagram, you can see the replacement parts that Yakima offers for your Ridgeback Bike Rack. If what you're needing isn't shown, please let me know what you're needing. Zip strips #Y8890297 Endcap #8890306…

view full answer...

Answer 5

I reached out to my contact at Yakima and the change made to the Ridgeback in November 2015 was most noticeably made to the cradles. The older style cradle had a gray button to release the zip strips and the newer style has a black button for the zip…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Replacement Zip Strip Recommendation for a Yakima RidgeBack 4 Bike Rack

Products Featured in This Question

Continue Researching