bing tracking image
  1. Trailer Bearings Races Seals Caps
  2. etrailer
  3. Bearings
  4. Standard Bearings
  5. 10000 lbs Axle
  6. 9000 lbs Axle
Replacement Trailer Hub Bearing - 387A
etrailer

Replacement Trailer Hub Bearing - 387A

Part Number: 387A
In Stock
$34.08
Trailer Bearings Races Seals Caps
Add to cart
zoom in icon
slider vertical icon
zoom out icon
Comment field cannot be left empty.
Name field cannot be left empty.

Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.

Error submitting comment. Please try again momentarily.

Product Images

Need help with installation?
Locate installers near me
High-quality, tapered roller bearing is designed for high-speed use. Replacement part uses industry-standard number. Great Prices for the best trailer bearings races seals caps from etrailer. Replacement Trailer Hub Bearing - 387A part number 387A can be ordered online at etrailer.com or call 1-800-940-8924 for expert service.
  • All Info
  • Reviews (45)
  • Q & A (0)
  • Videos (2)
  • Photos

etrailer Trailer Bearings Races Seals Caps - 387A

  • Bearings
  • Standard Bearings
  • 10000 lbs Axle
  • 9000 lbs Axle
  • 2.250 Inch I.D.
  • Bearing 387A
  • etrailer
  • Race 382A

High-quality, tapered roller bearing is designed for high-speed use. Replacement part uses industry-standard number.


Features:

  • Inner diameter: 2.250"
  • Matching race (sold separately): 382A
  • Application:
    • Inner bearing for 8-288-3 hub
    • Inner bearing for 8-214-5 hub


387A Replacement Bearing





Video of Replacement Trailer Hub Bearing - 387A

Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.




Video Transcript for Trailer Bearings Races Seals and Caps Rebuild

Speaker 1: Today we're going to take you through the rebuild process on a couple of hubs. We've got an idler hub, and here we've got a hub and drum assembly. Works with electric rigs, but this can also work for just standard discs, if you've got a disc brake style setup.Basically what we're going to show you is how to get all of the bearings out. How to remove the seal. How to remove the race's if they're damaged, then get them replaced in the proper manner. We'll show you how to use an easy loop hub, which we have here.The first thing we are going to need to do is, get the grease cap off the end.

It can have either a rubber plug in it like this one does, or it can be a solid metal cap.These are pressed fit in there, basically by tapping on them on the back side. To remove them, a deadbolt hammer is typically what we're going to use. We're just going to start tapping as we go around. You'll see a little separation start right here, and slowly it'll work it's way off.Now the next step's going to vary a little bit depending on your axle setup. Do you see this is going to have a keeper that goes around the nut.

And that prevents that from being backed off, or removed. A lot of times you'll have a castle nut, which will have just little tabs that stick off, and there will be a cotter pin that passes through it. Just depending on your application, you need to get the keeper for the nut off. This style we just kind of pry out. A cotter pin you would just remove of course.Once we have that off ...

We'll start to take off the nut here, and the washer that's in behind it. Now yours should look a whole lot more dirty than this. There should be a lot of grease packed in, and through the hub, this one's brand new. We thought it'd be nice to show you the components before the grease was on .. Of our washer that comes off.And then here we're going to have our outer bearing.

Continue to pull that. We're gonig to have our inner bearing here. That sits in the backside of the hub. And we didn't put it in yet, we will show you how to put it in. But a seal would typically be covering the backside here. We'll show you how to use a seal removal tool, or another tool. To get that pried up and out. To get an access to that inner bearing.Now for a drum style like this, that process for disassembly is going to be just the same. One thing to keep in mind if you're using a disc brake setup. You'll have to remove the caliper before the disc is going to come off.Now once we have the spindle exposed, as we said this is going to be really greasy. We want to get all the grease removed, and the first thing we'll do is inspect it. We want to make sure that it looks just like what we have here. Everything's nice and smooth. We don't see any kind of discoloration, or any marring on the metal. Indicating that our bearing's got hot.If you do have any of those symptoms, at this point it's time to replace those bearings. You don't want to repack them. Get new bearings, and put in there. You might have a bearing that's come apart in here. Another surface to ensure is in good condition, is where your seal is going to go. That helps seal all the grease inside of our hub. With a damaged or broken seal, that grease is going to seep out. Either out of the hub, or in this case into our brake assembly.Now if your axle has brakes, we're also going to check the disc. Make sure it doesn't have any issues, or your hub. And this is going to be a hub and drum assembly. The brakes are going to ride on this machine surface. You're going to check that for signs of excessive heat, discoloration, or cracking. And this is our magnet surface. We'll check that surface for the same issues.Now inside the hub regardless if it's a disc brake, it's a drum brake like this. Or just a standard idler style hub. You're going to have an outer race. Would be right here, it's a small tapered piece of metal your bearing sits in, and rotates on. That's basically the outer portion of the bearing.You have the same thing here on the backside. This is called the inner race. Now if those show any signs of wear, overheating, or cracking. Those are also something we'll need to replace, which we'll show you how to do in just a minute.Now, with your brake assembly exposed, if you do have electric brakes like we have here. It's a good idea to check all the components for wear, cracking, maybe missing pieces. Check your pad thickness to make sure those are in good shape. Basically if you have a non working brake assembly and you put everything back together, you're just going to have to take it apart and do it all over again to get back to the brake assembly. This gives you a really good option to be able to change them out.And most applications are going to use a four, or maybe a five bolt flange to hold them in place. And you'll just remove the lock nuts, or sometimes you'll have a hex nut with a lock washer. You want to remove those, and then simply slide your assembly off after you cut the wiring.The friction material itself should also be checked for any kinds of cracking, or overheating. If you have any grease inside the system at all, it's likely it's gotten on those pads. It's a good idea to get those changed. Now as far as the removal of the races go, it's going to be just the same whether we're using an idler style hub like we have here. A drum brake like we have here. You can basically see where the idler is, here in the middle of the hub. It's going to go all the way around there, and we just have this extra material here to provide our braking surface.Now if you're doing a disc brake style job again, it's going to be just the same here with the races living inside of the actual hub portion. You'll just have the discs there for the brakes to make contact. We're going to use this little bit smaller one, it's a little bit easier to manage to show you how to get these out. We've talked about where the races are. The outer here, the inner being closer to the inside, but on the backside of the race there's a little lip. That lip's meant to stick out just a little bit further than the hub, and provide us an area to put our tool on, and help to drive that out.If you look all the way through there on that inner race, you'll see that little lip that sticks out just from the hub slightly, and it gives us enough area to use our tool on. Now generally to remove these you're going to use a punch, similar to this. Some guys will use a screwdriver. Or a piece of pipe. If you have a piece of pipe that's small enough to fit inside of that diameter, you can take that down through and allow it to rest on that lip.Use our punch, and then just need a hammer. And we'll start working that out. We're going to tap all the way around. Kind of equally, and evenly apply the force to get it to come on out of the bottom for us.You can see now as it starts to come out there's going to be a little gap created between the hub and the race. And we can just keep going, bringing it on out. Then you can inspect the inside of the hub surface there. Make sure no damage or anything has occurred, and repeat that same process for the outer race if you plan on removing and replacing that one.Now in the outer flat edge, you can see we're going to have our tapered edge on this side. If we roll our race over to the flat side, typically there's going to be a manufacturers part number on there. That will help you identify which race it is, that you need to go back in your system. If those are rubbed off, worn off, if you can't read them. You can measure the outside, to outside diameter of the race here. It's a good idea to use a micrometer to get it exact.Now here's your basic micrometer. And again, the outside of the race is what we're going to need to measure. You want to go . I set the thickest point there. Looks like this one's going to be about 1.98. That's going to be the measurement you'll want to supply.Now while we've got this out, let's also look at the proper way to measure our bearing. Instead of the outside for the bearing, we need to measure the inside diameter. That's going to be pretty simple. Let's pull that out, find the largest measurement we can. Which here, looks like it's going to be 1.03. With that information, we'll be able to get the correct bearing, and the correct race, so they'll fit together properly and make a full bearing kit for us.Now here's the race, we're going to show you how to get this put back in. Basically just going to press fit inside of our hubs. We need to get it down on there. Kind of like that. And you'll have a couple options. A lot of times you're going to see do it yourself or at homer, just going to use a wooden block. Just place it on there. That's going to get you started, but at that point you'll struggle in getting it to go all the way down into it's seat.Now to take care of that problem, there are several seal drivers that are available. Seal and race drivers that are available out there on the market. It's designed to fit down inside of our race, inside of our hub and get it down there where it needs to go. This is part number ptw83020, has several different sizes, even if you have multiple trailers it's going to do the job.Now the side with the angle on it, is designed to fit down inside of our race. If we use the other side, that's going to be for driving your seal into place. Just want to hold it, and take it on in with your hammer. You'll see, you just want to insure that our race is all the way up against that line on the hub where it's supposed to mate to.Now when it comes time to pack your bearings you're going to have several different ways of doing this. You can just use your hand, is the traditional method. That's going to be the method probably reserved for the very occasional trailer work kind of situation. If you do it once or twice a year, probably get away with it that way.Next you would go to a, kind of a sandwich funnel style almost. If you look inside of there, you can see the bearing. It's located between the two pieces. Just use a grease gun. Start filling that with grease, and that's going to fill our bearing for us. And the third, with this one you're just going to place your bearing down and in. It should be pretty close to center. And then we've got our cone her that's going to go down and secure that.Now I think this style, wastes a little bit more grease than what this style will. This has a dust cap. You can see, you can keep your grease in there, put your dust cap on there and save it for later use. This will be if your going to do it every couple years. And this particular style would be if you're a more regular user.Let's start by showing you how to use a bearing packer. Similar to this. Again, we've just got our grease inaudible 00:11:07 here on the top. And then just slowly start to fill it. Now I like this style quite a bit. I think even regular users might enjoy it, because you can get a really quick visual look at that bearing. You're not going to have to overdo it, or have to much grease.You can kind of see in there now, we're starting to get grease to come out of it. Couple more pumps, we'll be good. You can see we've got grease coming out all the way around. Where all of our bearings are. Got a little bit of excess there. Just take that around the outside of it. And then we should be able to lift it off. And now you can see what we we're talking about. Just a little bit of excess there, that you're just going to wind up wasting.Now we'll take our bearing, we're going to place it right down in our race. And then we'll cap off the back with our seal. Right now our seal's going to fit in just like our race did. It's going to have a little bit of a pressure fit to it. Now very often in this situation, I see people using the four by four method. Kind of here, just placing that on and tapping it. As an option though, if you do have one of these. You can see that's designed to fit right on the top of the seal. And help drive it in.The biggest thing here is, just going to be getting it driven in squarely. You can see, this side's in a little bit further than this side. I'm going to start this side first. Now since we didn't have the opportunity to show you before, we're going to take a look at pulling a seal. Now this is a seal puller, we carry this on our website part number ptw1219. This is meant to hook underneath the seal. And then you kind of pull up on it, and just like our race you'll have to work all the way around that edge. Just bringing it out a little at a time.If you don't have that available. Another option would be a screwdriver. You just kind of get that under the seal, and turn it. And see, that'll allow you to also pop that out. We've taken care of our race. Our inner bearing. Our seal. The last component, before we put our hub back in place is going to be our outer bearing. Now with this bearing, I'll show you the hand packing method.This is definitely . Slightly dirtier method than the bearing packer. When we get grease on our hand we want to look at the larger side of the bearing. This is the smaller side. We have a larger side In between the inside and outside there's a gap. We can see our rollers in there. We want to grab that, and use that gap and shove grease inside of it. Now this is going to take a little bit, you want to work in the same spot until you get the grease pushed all the way through. We can see on the top there we've got a little bit starting to come through.And once we push it in the bottom, and you see it start coming out the of the top in those little drips, it's going to indicate that, that section's fully packed. Just need to work all the way around their outside edge now and do the same thing. Alright, once that's all the way around . The bearing will be ready for use.Now one more thing I like to do. We can see our inner bearing there, and our outer bearing. Well between the two, got a pretty big gap in there. If you'll take a . Pretty good amount of grease. We're just going to go all the way around. See how we can go all the way around the inside and just line that really well. The more grease we have in here, the less chance we have of any moisture getting in there, which can cause corrosion, rust, pitting. Pretty much things we do not like when it comes to bearings, races, and hubs.Put plenty of grease in there. And then this one does have the easy lube spindle, that'll even fill it in more. Now we can get our assembly slid on. I like to keep my thumbs on that outer bearing, just to prevent it from . inaudible 00:15:28 pushed off there. Now we can put on the original hardware that we removed, in taking off our hub the first time. In our case, we had our washer and our nut.Now most commonly you'll see pliers similar to this being used. We basically want to get that tightened down. Once it's fully tightened down you'll feel some resistance in the hub. We back it off just slightly. That'll give us a little bit more freedom of motion there. Something you don't want however . Is any movement in, or out on your hub. You want to be sure that everything is compressed, and you don't have what's called end play. Which would be the play in and out.Once we've got that set, then you'll put on whatever tight keeper yours came with. Get that put back in place. Now with an easy lube style hub, you're going to place your grease gun on the end, and then you can just fill the remainder of that hub up.Now for your typical applications, you're either going to have a solid cap, or a cap that'll have a rubber plug in it. A solid cap's going to be for an axle without the grease inaudible 00:16:51 here on the end. Goes on there. Just knock it on with your rubber mallet. Same with the one with the plug. Just gives you a removable area there, be able to cap that off.We'll show you how to put that on. Now as alternatives as well, a lot of times on boat trailers and marine kind of situations. You'll see a bearing buddy. This is going to apply a little bit of pressure on the grease, you'll fill it up. This kind of comes out just a little bit. That applies constant pressure on the grease to make sure we don't have any air, or anything like that. Then there is also an oil bath hub available. Now this is going to be for use with seals that are going to be designed specifically for oil bath use. You'll have to change that seal.We're using a double lip seal. There are also single lip seals available. Of course a double lip seal is going to give you just a little additional security. Keep that in mind when you order. But let's get this knocked on there now so you can see how that works. We just want to take the cap, we're going to center it. This is going to be very similar to what we did with the seal. And then just gently start tapping it around the outside. And it'll seep down on there for you.It's really going to be the same thing that you'll do with any of the end caps. Now with this side done, it's a good idea to take care of all the other hubs. Get them all on the same maintenance schedule. And as long as you'll periodically check the grease, take your trailer out for a trip occasionally. Just to keep everything lubricated. It should extend the life of these parts, and give us years of good service.

Customer Satisfaction Score:


Customer Reviews

Replacement Trailer Hub Bearing - 387A - 387A

Average Customer Rating:  4.6 out of 5 stars   (45 Customer Reviews)

High-quality, tapered roller bearing is designed for high-speed use. Replacement part uses industry-standard number.

by:

Sheila was the best! She knows her stuff and got me all the right part numbers and items for a 10,000# double axle brake rebuild. Brakes, bearings, races, seals etc. Shipping was quick and the couple B/O items shipped a few days later as she indicated. Now all I have to do it is put it all back together.



by:

Excellent Quality!



by:

Package arrived when promised and product worked as it should



by:

Great product and fast service. I will be back I have other trailers and I have told several or maybe even many people about you. Thank you so much These were mostly bearings and seals for a heavy trailer so I don't have any pictures. Take my word for it though with them



by:

Perfect fit



by:

The product was as advertised.. Obviously nothing special about a bearing. But, the service that etrailer.com provided was exceptional.



by:

This place is awesome to order from correct parts first time. I ordered parts about noon and they were on my step the next day.



by:

Quality Part



by:

This was an easy buying experience. The sales representative was extremely helpful and very patient. I am not the end user for the items I purchased so I can not speak to that but, the service was excellent!



by:

Made in china bearing, came in a plastic bag; hope they last a few years!



by:

Fit and worked as it should



by:

Great buying experience. Found everything I needed on the easily on the website.



by:

These guys are great. Best service I have received. No reason to shop elsewhere.



by:

great, it fit perfectly



by:



by:

Quality



by:



by:



by:



by:



by:



by:



by:



by:



by:


25
45
Show More Reviews

See what our Experts say about this etrailer Trailer Bearings Races Seals Caps

  • Replacement Bearings, Seal, and Brake Assembly for Dexter D1012 HD Axle
    The bearings you need for a Dexter D1012 HD axle would be: Inner bearing # 387A Outer bearing # 25580 Oil seal # 10-51 For brake assemblies you'd need the # 23-438-439 which are a 12-1/4 inch by 4 inch wide assembly.
    view full answer...
  • How To Convert Dexter Electric Drum Brakes to Hydraulic Disc Brakes on 10K Axle
    In order to convert a Dexter 10K Axle (Made After May 2013) from electric drum to hydraulic disc brakes you'll need the following: Kodiak Disc Brake Kit part # K2R1058D11E (1 per Axle) Dexter Oil Hub for 9K to 10K General Duty Axles part # 008-430-03 (2 per Axle) Inner Bearing part # 387A (2 per Axle) Outer Bearing part # 25580 (2 per Axle) Oil Seal part # 10-51 (2 per Axle) Replacement Oil Cap Kit part # RG04-300 (2 per Axle) Hydrastar Electric Over Hydraulic Actuator Kit part # HBA16-252-82...
    view full answer...
    Image 1 for Image 2 for
  • Bearings, Seal, & Electric Brakes For Big Tex 22GN 35+5 Gooseneck Trailer
    I was able to find the correct electric brakes, as well as oil seal (which is what I assume you were referring to by wheel seal), and also the bearings for your Big Tex 22GN 35+5 gooseneck trailer. I'll go ahead and list out the parts for you below. - Oil Seal # 10-56 - Replacement Trailer Hub Bearing # 395S & Race # 394A - Replacement Trailer Hub Bearing # 387A & Race # 382A - Dexter Electric Trailer Brake Assembly - Left Hand # 23-438 & Right Hand # 23-439
    view full answer...
  • Replacement Bearings, Races and Oil Seal Used In Dexter Bearing Kit K71-722-00
    While we do not have a kit that includes everything from the Dexter K71-722-00 bearing kit we do have all the parts that are included with the kit. Inner Bearing # 387A Inner Race # 382A Outer Bearing # 25580 Outer Race # 25520 Oil Seal # 10-51
    view full answer...
  • Replacement Brake Assemblies for Dexter 10k Axles on Gatormade Trailer
    We have what you need! Thanks for the photos. Even though the serial number is torn from the axle tag, we still identified the brakes you need with the Unique ID Number 124394998016 from your 10k Dexter axle tag. I confirmed with my tech at Dexter that you need the Dexter Electric Trailer Brake Assembly - Self-Adjusting - 12-1/4" # 23-450 (left side) and the # 23-451 (right side). These are direct replacements of brakes constructed for your 10k Dexter axles on your Gatormade trailer.
    view full answer...
    Image 1 for
  • Replacement Parts For Dexter 10,000LB Trailer Axle On 2019 PJ Trailer
    Your Dexter axle SN 125272197 came with the Dexter Electric Brake Kit # 23-450-451. It uses the following bearings and seals. Inner Bearing # 387A Outer Bearing # 25580 Inner Race # 382A Outer Race # 25520 Oil Seal # 10-51 Oil Cap # RG04-300
    view full answer...
  • Is Dexter Hub Drum Assembly # 8-430-5UC3 Available in Individual Parts?
    The Dexter Trailer Hub Drum Assembly - 9K to 10K - 8 on 6.5 - Oil Bath - Non-ABS Drum - After July 2009 # 8-430-5UC3 comes as the complete kit and the hub/drum is not available separately. The bearings, races, seals, and caps are available separately: Inner Bearing # 387A Outer Bearing # 25580 Inner Race # 382A Outer Race # 25520 Oil Seal # 10-51 Oil Cap Kit # RG04-300
    view full answer...
  • Determining Replacement Hub And Bearings For Dexter P-12 SLR Trailer Axle
    I can definitely help you find the correct replacement hub and bearings for your Dexter P-12 SLR axle, but since part of the serial number was unreadable you will need to take a few simple steps to identify which bearings your axle uses. The easiest way to accomplish this is to remove one hub and look for the numbers stamped on the inner and outer bearing like shown in the attached picture of the # L44649. If your bearings are too worn to be able to read the numbers, you will need digital...
    view full answer...
    Image 1 for Image 2 for Image 3 for Image 4 for Image 5 for
  • How to Determine if Kodiak Disc Brake Kit Will Fit Dexter Axle 10K HD Axle
    The Kodiak Disc Brake Kit # K2R1058D11HD will fit your Dexter 10K HD axle if your axles uses the Dexter K08-288-91 hub, which we have as part # 8-288-3UC1 on our site. This hub uses a # 387A inner bearing, # 25580 outer bearing, and an oil seal with a 2.875" inner diameter. Attached are some review videos for you to check out.
    view full answer...
  • Bearing Recommendation for a Dexter 10k General Duty Axle
    For the Dexter General Duty 10k axles the recommended bearings that we carry are the inner bearing # 387A, outer bearing # 25580, race # 382A, and race # 25520. We have confirmed with Dexter that these are the correct parts.
    view full answer...
  • Replacement Bearings and Brake Assemblies For 1998 Dexter 9000lb Axle
    Thank you for the pictures and information of your axle! I called Dexter and your Dexter P12 SLR axle with Serial Number D-423-4057 has a 9000lb axle rating, and uses an 8 on 6-1/2 hub and drum assembly with 5/8" studs like you mentioned. For replacement bearings there is not a kit that has all of the bearings and races but you can purchase them all separately as follows: Inner Bearing # 387A Inner Race # 382A Outer Bearing # 25580 Outer Race # 25520 Oil Seal # 10-51 And Oil Cap Kit...
    view full answer...
    Image 1 for Image 2 for Image 3 for
  • Will Dexter 9K - 10K Hub and Drum Fit Lippert 10K Axle
    Hub and drum assemblies, like the Dexter # 8-430-5UC3 you referenced, are universal so they typically fit any 9K - 10K axle just fine. With that being said, there are some exceptions out there so you just need to confirm that your axle uses a # 387A inner bearing, a # 25580 outer bearing, and that the inner diameter of your grease seal is 2.875" to ensure that this fits. Pull your current hub and check the numbers on your bearings to confirm this. If you can't find the numbers then Lippert...
    view full answer...
    Image 1 for
  • Bearings For 10,000 Lb Dexter Axle
    My contact at Dexter was able to use your Dexter Axle number 4389878 and Serial number 125263858 to find the bearings. She said your hub uses outer bearing 031-030-02, outer race 031-030-01, Inner bearing 031-019-02 and Inner race 031-019-01. These parts are equivalent to the inner bearing # 387A outer bearing # 25580 and race # 382A and race # 25520.
    view full answer...
    Image 1 for
  • Availability of Spindle and Hubs for 10,000 lb Trailer Axle
    As you may have noticed, the highest capacity spindle we carry is for a 7,000 lb axle, # TRU37FR. Your best bet is to source the spindles for a 10,000 lb axle through a local trailer shop or dealer. If are able to source the spindles, we do have hubs for 10,000 lb axles. I'll list them below: # 8-430-5UC3 - Dexter Hub Drum for 9K to 10K axles manufactured after July 2009 (for non ABS brakes) - uses inner bearing # 387A, outer bearing # 25580 and oil seal # 10-51 # K08-288-90 - Dexter...
    view full answer...
  • Technical Drawing for Dexter Hub Assembly # 8-214-5
    I spoke with my contact at Dexter and was able to obtain the technical drawing for the Trailer Hub Assembly, # 8-214-5. Keep in mind that this hub was designed to fit a spindle from a 10K Dexter axle. I have attached this drawing for you. We do offer part # 8-214-5UC1 which includes the trailer hub assembly, lug nuts, inner bearing ( # 395S ) and race, outer bearing ( # 387A ) and race, oil seal and cap. These are designed to fit 10,000-lb axles with spindles that require a 3-1/4" ID grease...
    view full answer...
    Image 1 for
  • Replacement Bearings For Dexter Model D1012 Axle
    Thanks for the picture! I sent that over to my contact at Dexter and your axle uses the following components: Inner bearing # 387A Inner race # 382A Outer bearing # 25580 Outer race # 25520
    view full answer...
    Image 1 for
  • How to Pick Out Bearing for 10,000 lb Dexter Axle
    We have the bearing part # 387A which is over 2 inches in inner diameter and is seen on 10,000 lb axles but I'd have to know exactly what your spindle dimensions are to know for sure what you'd need. If you can use a digital caliper like the # PTW80157 to get me the exact dimension of the spindle where the bearings and seal ride I'll be able to let you know which parts you need. A very common bearing combo for Dexter 10k axles is # 387A and # 25580. Races needed are # 382A and # 25520....
    view full answer...
    Image 1 for
  • What Is the Weight Capacity Of a Dexter D100G Axle
    The spoke with Dexter and the code "D100G" tells me you have two 10,000 lb trailer axles. I have attached some parts you may need for the axle below. Dexter Trailer Hub Drum Assembly (After July 2009) - part # 8-430-5UC3 Dexter Trailer Hub and Drum Assembly (Before July 2009) - part # K08-288-90 Dexter Electric Trailer Brake Kit (12-1/4" x 4") - part # 23-438-439 Dexter Hydraulic Drum Brake Kit (12-1/4" x 4") - part # 23-404-405 Inner Bearing - part # 387A Inner Race - part # 382A Outer...
    view full answer...
  • What is the Capacity of a Dexter P-12 Model D100 Axle
    It looks like you're likely trying to replace your hubs/drums on your Dexter axle and I do believe that the "0100" you found on the spec plate actually reads "D100" since that was one of the models that Dexter had for this particular line of axles; I've confirmed this with Dexter as well. These axles were 10k axles and they came in both a general duty and a heavy duty model with the 10k capacity. In order to find out which hub/drum will work as a replacement, you'll need to pull the hubs...
    view full answer...
  • Recommended Brakes, Bearings and Seals for Dexter 10k General Duty Axle
    I reached out to Dexter and found that your axle is a 10,000 lb general duty axle. The correct inner bearing and race is the # 387A and # 382A, the correct outer bearing and race is the # 25580 and # 25520. For a replacement seal you want the # 10-51. For electric brakes I recommend the Dexter Electric Trailer Brake Kit - Self-Adjusting - 12-1/4" - Left/Right Hand Assemblies - 10K # 23-438-439. These are self-adjusting brakes so there will be no need for manual adjustment. I have attached...
    view full answer...
  • Converting to Electric Over Hydraulic Disc Brakes on 2021 Diamond C Trailer
    According to Dexter, the Kodiak Disc Brake Kit # K2R1058D11E is compatible with your 10,000 lb Lippert axles. For idler hubs you can use the Dexter Oil Hub # 008-430-03. From there you will need the Hydrastar Electric-Hydraulic Actuator w/ Line Kit # CAR-HBA16-2. This comes with the brake actuator as well as the hydraulic brake lines. If you don't already have a breakaway installed, I recommend the Bright Way # 3802308. If you need a brake controller as well, you can use the # RED24FR...
    view full answer...
  • Replacement Hub Options For a Dexter D1012 With Bearings 387A and 25580
    Here is your options for a Dexter D1012 with the Inner Bearing # 387A, Inner Race # 382A, Outer Bearing # 25580, and Outer Race # 25520. Idler Hub Prior July 2009 # 8-288-3UC1 Idler Hub After April 2013 # 008-430-03 Hub/Drum Prior July 2009 # K08-288-90 Hub/Drum After July 2009 # 8-430-5UC3 All but the Idler Hub After April 2013 # 008-430-03 include all the bearings and seals. For this you will have to also add the following components for each hub. Inner Bearing # 387A Inner Race #...
    view full answer...
  • Replacement Oil Seal Needed for Older 9K Dexter Axle
    I spoke with my contact at Dexter Axle who said that your axle is rated for 9,000 lbs and uses the inner bearing # 387A, outer bearing # 25580, and seal # 10-51. This seal has an inner diameter of 2.875" and an outer diameter of 3.880". I would verify that this is compatible with your hub by using a digital caliper that will measure to the thousandths place (three decimal places).
    view full answer...
    Image 1 for
  • Replacement Hubs and Bearing Parts For a Dexter 10,000LB General Duty Axle Prior To July 2009
    Your Dexter axle is a 10,000lb general duty axle that was manufactured on 1/31/01. That is all information I was able to obtain from Dexter due to the age of the axle. It will use either the Dexter Trailer Idler Hub # 8-288-3UC1 or the Dexter Trailer Hub and Drum Assembly # K08-288-90 with the Dexter Electric Brake Kit # 23-450-451. If you are looking for a bearing kit you will need to get the following components as we do not have a kit with everything you need. Inner Bearing # 387A Inner...
    view full answer...


< Previous
12



Do you have a question about this Trailer Bearings Races Seals Cap?


Info for this part was:

Employee Jeff D
Installed by:
Jeff D
Employee Jameson C
Expert Research:
Jameson C
Employee Chris R
Video Edited:
Chris R
Employee Wilson B
Updated by:
Wilson B

At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.