While we don't have replacement parts for a Model 70LP actuator, we do have a great replacement for it. Like the 70LP, these actuators are a fit for a 2" hitch ball, but they just have a slightly larger capacity at 7,500 lbs. You didn't…
The towing capacity of the 2003 Chevrolet Avalanche 1500 with 5.3L V8 and 4.10 rear axle is 8100-lbs. For a 7600-lb GVWR travel trailer the resulting 500-lb safety margin is adequate/low-ish. With a trailer that weighs substantially more than the tow…
Hi Kassi! I do have a couple options that will fit your 2024 Chevy Colorado WT with 2 wheel drive, but the Timbren Suspension Enhancement System - Rear Axle #T83AV is specifically for the 4 wheel drive models. With that said, you will want one of the…
Hey Rick, yes you can use the longer Equalizer shank part #EQ90-02-4500 that you referenced in place of what you have now to get a little more length from your towing setup. While this is longer and would in theory apply more leverage it doesn't…
I would be happy to help you. For your 2006 Kenworth T300 I recommend the Tekonsha Prodigy P2 Trailer Brake Controller item #90885. This controller ties into the brake stoplight switch that's usually located above the brake pedal, which is what…
Hey Brad, to replace your Tie Down Engineering LP70 actuator, I recommend going with the Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-20. This actuator will fit on 3" wide channel tongues, will work with 2" balls, and has a 7,500 lb…
The Furrion #FACR15SA-PS 15,500 BTU unit that you referenced is a replacement for Furrion only and is not offered with compatible ceiling distribution box. I do have a solution though. To replace your Single-Zone, Stand-Alone Dometic Duo-Therm Brisk…
If the front arm/hinge on your Yakima SkyBox Cargo Box like the SkyBox 12 #Y07334 isn't unhooking due to the carrier being over-stuffed, then your only real option is to try and wiggle around your cargo enough to get some clearance between it and…
Based on the number you mentioned you have a 3,500 lb AxleTek hub so for a version that has the 6 on 5-1/2 inch bolt pattern you are wanting you'd need the part #AKHD-655-35-EZ-K.
The exact replacement hub assemblies you need for your BD2-545-17 are the etrailer Trailer Hub and Drum Assembly - 3,500-lb Axles - 10" Diameter - 5 on 4-1/2 #AKHD-545-35-K that you referenced.
Hey Neil, so we can help but we don't have a rebuild kit or an exact replacement for the Tie Down model 70lp that you referenced. The Dexter Disc #DX73FR or Drum #DX67FR actuator is going to be your best option. These are weld on actuators but we…
Measure your tailpipe's outside diameter and match it to 3 inch diameter for a proper fit. Choose clamp-on for quick installs or weld-on when you want a permanent setup, and look for angled styles if you need to divert heat away from cargo. For a black look, use high-heat spray paint on the tip; tailpipe temps are far enough back that quality paint holds up.
Yes, choose a tip with the outlet angled downward to redirect flow. This style is available for a 3 inch tailpipe and helps move heat away from cargo. These angled versions are typically weld-on, so plan on a professional installation and verify you have enough straight pipe to attach it.
If a black version isn't available, you can paint a 3 Inch Diameter tip with high heat black spray paint. Exhaust tips are far enough from the engine that the paint can hold up well. Avoid using the same paint on headers, as the higher temperatures can cause it to fail.
Measure the outside diameter of your tailpipe. A 3 Inch Diameter tip is designed for a tailpipe with a 3 inch outside diameter, and you'll need a long enough straight section to mount it. If your measurement isn't close to 3 inches, pick a size that matches your actual OD.
Both work; choose what suits your install. Clamp-on is convenient if the fit is right and you want easy removal. Weld-on provides a more permanent mount and is recommended for angled redirect tips; have a certified professional welder install it. If the pipe is slightly undersized, an exhaust shop can sleeve or expand it to fit.
Filters
