# 1
Curt Ball Mount w/ Sway Control Tab for 2" Hitches - 3/4" Rise, 2" Drop - 7,500 lbs
I cannot use this ball mount because the shaft is too short that goes into hitch receiver on my one ton Dodge truck. It does not allow enough room between truck back bumper and ball to allow any trailer tongue to be put on ball.
I purchased this for use with a friction anti sway device I installed on an enclosed V nose trailer. It worked well.
# 2
Curt Multi-Ball Adjustable Ball Mount for 2" Trailer Hitches
Fits our VW Touareg perfectly and allows us to tow a variety of things now. As can be seen in the pictures the hitch has a +5-inch gap between the bumper and the vertical adjustment pillar and the trailer itself is out further so there's enough room to get to the rear hatch and maneuver the vehicle/trailer.
I needed a hitch that I could haul my work trailer with and still drop the tailgate without dropping the trailer. I looked on etrailer and found one that would work barely but decided to call etrailer and see if anyone had any ideas. Steve answered and looked after I told him my requirements and came up with this. This has a longer distance from ball to pin by a few inches compared to the one I found so my tailgate will still drop even if I’m at an angle to my trailer or on a hill. Also with the adjustable height it’s great. Awesome hitch. Solid for a good price. ??
# 3
etrailer Ball Mount Kit for 2" Hitches - 3/4" Rise or 2" Drop - 7,500 lbs
Thank you etrailer for the quality products I received early last year. We needed a trailer hitch to install on our Subaru Forester for our move from Gig Harbor, WA to Spokane. We received the hitch hardware including the tow bar and electrical harness. The entire process took 4 hours. The installation process went off without a hitch (bun intended) using detailed videos I found online. Thank you etrailer.
I must say I like having my etrailer equipment installation was easy. But I really wish I had installed the factory hitch. Only because the provisions for mounting the wire harness is much much better. etrailer IS GREAT WITH ALL THAT THEY DO
# 4
Draw-Tite Ball Mount for 2" Hitches - 2-3/4" Rise, 4" Drop - 9" Long - 7.5K
To be honest, I use it upside down. I needed a hitch with rise, but none were available at time of purchase, and yours, inverted, works perfectly! The welds are regularly checked and remain all secure. It's a good hitch.
Working in the sand and grass of my driveway my wife and I installed our new etrailer receiver hitch. Great fit and finish! Went right on as described in the online guide. Hitch required a spacer washer on top back bolt attachment point. Taped it on so it would not move while lifting in place and it stayed right there! Used a car jack to raise up and hold the hitch into the underside of the trunk tighten the bolts and reattached the tail pipe done. Now we can pull our Sunfish Sailboat any where the car will go.
# 5
Draw-Tite Ball Mount for 2" Hitches - 5" Rise, 6" Drop - 10-1/4" Long - 16K
This ball mount fit the SUV just right. I needed a 5 inch rise and the mount angled away from the bumper. However, the load capacity was way more than I needed, but the fit made up for that. It's a little loose in the receiver so I will be adding a stabalizer to lock it in place.
Did not work on my truck due to custom rear bumper. Looks great on my friend's 2018 F350 4 X 4 diesel!
# 6
Pintle Hook Combo 2" Ball with 2" Shank, 12K
Excellent Quality... Best price and fastest delivery! Everyone with a towing package needs one of these in their vehicle...
Ordered 3 different hitched, each was exactly as described. Excellent quality. Ordered arrived very quickly. Will use etrailer again.
# 7
Hidden Hitch Ball Mount - 3/4" Rise, 2" Drop - 15-3/4" Long - 6,000 lbs
Very happy with this ball mount - provides just the amount of drop we required for a level tow of our GeoPro travel trailer by our RAM2500. Plus, the extra length not only allows a tighter turning radius, but also allows us to lower the truck tailgate without having to detach the trailer. Huge improvement on all accounts for us compared to our prior setup. The product is well built and I'm confident will provide us years of good use.
Great customer service. Live in SC - ordered a hitch and USPS delivered it to PUERTO RICO. Go figure. Stacey A refunded my money - but 2 weeks later hitch appeared on my doorstep. All’s well that ends well.
# 8
Curt Ball Mount for 2" Hitches - 1" Rise, 2-1/4" Drop - 7-5/8" Long - 7,500 lbs
This is a great all-purpose hitch. I've used it to mount a heavy-duty bike rack and a steel T-rack to carry a canoe as well as lumber. Most recently I hauled 5 x 8 cargo trailers full of plants, then furniture for a 600-mile move. It was simple to use, problem free, very strong and sturdy. Now that I live on some acreage, I see a trailer in my future, so this will get a lot more use. I drive a 2013 Tacoma, so this is a good size hitch at a good price with sufficient capacity for my needs. I do use a key lock for the hitch as well.
I actually got my hitch the date they said it would be here to my surprise. When the box arrived it was pretty much beat up, not the hitch just the box. I wished there was instructions how to install it. Overall very satisfied and will buy from 5hem again
# 9
Curt Multi-Ball Mount for 2" Hitches - Solid, Black Powder Coated Shank - Black Balls
Great experience
Product was just as advertised. Fast shipping. Good customer service.
# 10
Curt Multipurpose Ball Mount with 2" Receiver for Bike Racks and Cargo Carriers - 7,500 lbs
We sold our small motor home and purchased a small travel trailer. This hitch provided a perfect solution to how to use our bike rack while towing the trailer. It even allows room for the pickup tailgate to be lowered without removing the bikes from the rack. The hitch is very hefty with a high weight limit - plenty for the GVW of the trailer (7,000#) plus 125# of rack and bikes.
This has been an amazing multipurpose ball mount. We purchased this to use with our Hollywood Bike Rack and also to connect onto our boat. We weren't sure if this would work, but it was awesome. It is very well built and We had to make some minor adjustments to the position of our boat on the trailer so the turning radius of the bike rack that was attached would clear the truck. This is very well made and solid.
# 11
Curt Class III Ball Mount with 2" Ball - 2" Drop - 7,500 lbs
The hitch and ball mount are excellent quality. My concerns are twofold. The hitch is so heavy that I had to take it to my mechanic to have it installed. Minor cost and inconvenience, but the hitch for my previous F-150 was just as sturdy, but easy to install myself (albeit with higher ground clearance). My concern about the ball mount is that the factory told me erroneously that it could not be reversed for a drop, so I returned it. This order is for the replacement after I was finally correctly told it could be reversed and how to do that. Ball mount would have been a 3 for that reason, and overall hitch and ball mount quality a 5. So I averaged them.
I have two of these. My first I bought two years ago. I very highly recommend this Curt Class III Ballmount 2" Drop because of its price, durability and quality. I towed various class 3 loads with ease and confidence with this ballmount. It slides into the hitch and does its job without fail. It looks excellent after towing a load. etrailer's price is about as good as it gets and delivery is very speedy.
# 12
Flash Simple 2-Ball Mount w Chrome Balls - 2" Hitch - 6" Drop, 7" Rise
I like the look of this set very much and it is easy to mount and adjust the ball mount. The workmanship and finish are beautiful. Customer service was excellent in assuring I found the correct mount for my Ford Escape. I pull my 6'x10' utility trailer or very seldom my pontoon trailer. I like that the adjustable mount comes off very easily as I remove it until I need it while my vehicle is in the garage--it helps prevent knocking your leg against it in the garage. However, I am not having any luck loosening the bolt that secures the 2 chrome balls to the adjustable ball mount; I have the correct Allen wrench but cannot exert sufficient torque to loosen the bolt while the adjustable ball holder is off the ball mount. I want to put a different ball combination on so I can pull my son's trailer, which has a smaller ball than comes with the set, if I have to. I also added the anti-rattle device and it stops the mount completely.
This still looks good with no slop easy to switch between the different ball.
# 13
Curt Ball Mount for 2" Hitches - 4" Rise, 6" Drop - 9-1/4" Long - 7,500 lbs
I purchased Curt's 6" drop ball mount for my 2012 Jeep Wrangler Sport which is not lifted but has 32" tall tires. The utility trailer I plan to purchase recommends a 12" tongue/ball height for level towing. The Curt 6" drop ball mount places my tongue/ball height at 13.5" which is acceptable. The bottom of my tow ball mounting nut is now 12" above the road surface. Plenty of clearance for safe towing. I'm very pleased with the quality and functionality of my Curt ball mount. I'm looking forward to purchasing a utility trailer soon. I think it will tow very nicely using my Curt 6" drop ball hitch.
First class service from E Trailer, first class product from Curt, as always ! !
# 14
Curt Fusion Ball Mount for 2" Hitches - 2" Ball - 2-1/4" Drop - 7,500 lbs
I haul a 5.5x10 open trailer w/ a 900 lb. ZTR, a push mower, and a handful of other tools 3 days a week. It is what it is. It does the job, no problem. A little finish wear and rust on the ball, but nothing major. I LIVE ON A DIRT ROAD, which is probably responsible for the wear.
Well made.
# 15
etrailer Ball Mount Kit - 3/4" Rise or 2" Drop - 7,500 lbs
I bought the 1 7/8 and 2 inch combo so that switching between the two is as easy as pulling a pin. However, I didn't realize that I had to install the ball. I had to find someone with a wrench and torque wrench big enough to do it. Otherwise, excellent quality as usual from E-Trailer.
Easy to install and they feel really sturdy. Definitely recommend buying them with the carrying case as it makes them super convenient and easy to stow away when not in use.
# 16
etrailer Ball Mount Kit for 2" Hitches - 7,500 lbs
I'll start off with the great customer service, called a rep for assistance and did a great job. He walked me through everything for about 5 minutes. Then I proceeded to order parts at a very reasonable price. Shipping was right on time and tracking was top notch. Now for the parts I received. Trailer hitch receiver was built like a tank, and very easy to install. I didn't even have to take off the whole bumper which I see on your website. There is only one problem with this hitch receiver. Zip ties to hold the facia bracket? It's like putting a $10 paint job on a Rolls Royce. I'm sure you have a good R&D department, but this is unacceptable. I could tell you how to make this better but I'm not part of your team. Could be solved by putting a ___ on the ______. R&D should be smart enough and paid well to figure this out. No offense but they can do better. ??ZIP TIES?? Also, it is pitched with a cap but did not receive that. I also purchased A brake controller P3 and a ball hitch. The ball hitch is pictured wrong on your website. It's pictured with an adjustable ball hitch. This is what really wanted but got something entirely different. If it works, I'll be fine with it. I should have caught that, but my eyes adjusted on the adjustable ball hitch. P3 brake controller was very easy to install, about 5 minutes. On a closing note, I will order from etrailer again. Thanks for your business. Just please listen to your customers and fix these problems. Everything and everybody are not perfect. Thanks again.
The hitch assembly included everything needed for quick and complete installation. Perfect fit for my 2023 Honda Passport. Have been using etrailer for some years now and have never had a bad experience. The self-help videos are a plus for customer service. Good work guys!
# 17
Convert-A-Ball Ball Mount for 2" Hitches - 10-3/4" Rise, 12" Drop - 7,000 lbs
Arrived today. Fast shipping, and thank you for that! Seems to be a quality ball mount. Just what I needed to get the ball lower to tow my trailer. With this, now the top of the ball is at 16" where it needs to be. Custom built receiver on my old moving box van. Just need to weld on safety chain slots and paint it. Can't drop the lift gate with the receiver in (its pinned on both sides), but hey....I can tow now.
Tow infrequently; got new(to us) 2015 RAM 2500 pick up to tow our 38’ touring travel trailer. Have a HD WD hitch & adjustable sway control hitch set up we use for this trailer, but needed a drop hitch for our smaller Travel trailer& misc use haul trailer,,,,both much lighter & do not require the sway control set up. This drop hitch & ball fit the bill perfectly as the needed drop did not provide suffice t ground clearances to utilize the WD hitch mount setup (which was not needed) for those smaller loads. E-trailer worked w us to get the product we needed & an option that was inexpenve but sufficiently rated to pull our smaller trailers! Very happy our results !
# 18
Curt Tri-Ball Mount - 3 Chrome Balls - 10,000 lbs
Excellent product! With the three different ball sizes, this tri-ball mount gives you a lot of flexibility. Gone are the days of having several different ball mounts to fit different tongues. High quality construction makes this an excellent investment.
This item should solve the problem I have had with a stainless 3-way ball when I tried to reverse the position on the ball mount. The threads galled between the hex nut and hitch ball.
# 19
Curt Class III Ball Mount with 1-7/8" Ball - 2" Drop - 3,500 lbs
Very pleased with etrailer. Very easy to order from website. Fast delivery, easy to install ,perfect fit . Thanks. .
Perfect fit for 2 inch Draw Tite receiver. good price, fast shipping.
# 20
etrailer 2-3/4" Rise or 4" Drop Ball Mount Kit - 7,500 lbs
I purchased the etrailer.com 2-3/4 " Rise or 4" Drop Ball Mount Kit, Curt Trailer Hitch Receiver and Twist-in 7-Pole RV-Style Trailer Connector for my 2011 Chevy Silverado. Quick Delivery! All the necessary parts arrived in perfect condition. Directions were spot on and the instructional videos were great.
WOW! What can I say? Easiest install ever! I called ahead of time and spoke with Katie about what I needed. She confirmed what I wanted would work with my van. I'm in the shipping business. The bar arrived in mint condition in a double wall box with the accessories boxed separately. After removing the hardware, reading the instructions and watching their video online, I went to work. The whole thing took less than 20 mins and I did not have to remove the exhaust. I actually used it to help hold the bar up. It took longer to remove the mud guard and rear body molding than to install. It is heavy, weighing in at about 65lbs but I did not even have to use a jack on the van. I'm very happy with my purchase and can now put bikes on the back of the van rather than in the van. I can tow our Cub Scout trailer and hall my sons football teams gear with the optional rear carrying racks. I also love the fact that the bar hides about 6" behind the bumper preventing injuries to the shins. The price was cheap and the install a breeze.
Will the B and W Tow and Stow 3-Ball Mount Fit Your 2016 Nissan Frontier?
Today on our 2016 Nissan Frontier, we'll be doing a test fit of the B&W Tow and Stow 3 ball mount for 2 inch hitches. This has a 9 inch drop and a 9.5 inch rise. It's rated at 10000 pounds. The part number is BWTS10050B. We've already got our ball mount installed, as you can see. Going to go ahead and go over a few measurements with you with here, so you can keep that in mind. From the center of the hitch pin hole on our Frontier to the edge of where our ball mount sits, we have about 10.5 inches.
Does it Fit? Testing the B and W Tow and Stow 3-Ball Mount on a 2016 Nissan Frontier
Today on our 2016 Nissan Frontier we will be test fitting the B&W tow and stow 3-ball mount for 2-inch hitches. It has a 7-inch drop and a 7 1/2-inch rise. It is rated at 10,000 pounds. The part number is BWTS10049B. Now we have got out ball mount installed here already on the Frontier. We have got it installed using a pen and clip which is available on our website.
Diversi-Tech Adjustable Ball Mount Review - 2013 Nissan Frontier
Today on our 2013 Nissan Frontier well be test fitting the Divirsi Tech self-locking adjustable aluminum ball mount part number DTALBM6600. Before I begin our test fit well first need to obtain the hitch height of our vehicle which is the measurement from the ground to the inside top of the receiver tube. The hitch height for this vehicle is 17 inches. Keep in mind that this measurement may vary due to tire size, hitch style, or after-market accessories. Well now begin our test fit by sliding the shank of the ball mount in the drop position into the opening of the hitch. We can then turn the key to allow the integrated hitch pin to fall into place securing the ball mount to the vehicles hitch. We can now remove the key and adjust the ball mount platform to its lowest position. Unlocking the ball mount platform will also allow you to switch to the other size ball.
Installing the Curt Tri-Ball Mount on your 2013 Nissan Frontier
Today on our 2013 Nissan Frontier, we'll be test fitting the Curt Tri-Ball Mount for 2" hitches, part number C45001. Before I begin our test fit, we'll first inaudible00:00:11obtain the hitch height of the vehicle, which is the measurement from the ground to the inside top of the receiver tube 00:00:15.The hitch height for this vehicle is 17 and 1/4".Keep in mind that this measurement may vary due to tire size, hitch style, or after market accessories. We'll being our test fit by sliding the shank of the ball mount into the opening of the hitch and securing it with the pin and clip.Now since this ball mount has no drop or rise, if your trailer's ride height matches your vehicle's hitch height, this ball mount would be appropriate for you.The Curt Tri-Ball Mount is equipped with 3 different size balls. A 2 and 5/16" ball, a 2" ball and an inch and 7/8ths ball.This ball mount will allow you to carry different sizes and styles of trailers, without having the need to purchase additional ball mounts. With that, that'll complete today's test fit forthe Curt Tri-Ball Mount for 2" hitches, part number C45001, on our 2013 Nissan Frontier. .
Convert-A-Ball 6-Way Multi-Hitch Ball Mount Review - 2013 Nissan Frontier
Today on our 2013 Nissan Frontier we'll be test fitting the Convert-a-Ball cushioned six-way multi-hitch ball mount for 2-inch hitches rated at 10,000 pounds, part number CAV-6W. We'll begin our test fit by sliding the shank of the ball mount into the opening of the hitch and securing it with the pin and clip. You can rotate the ball mount to access three different size balls, an 1-7/8 inch ball, a 2-inch ball, and a 2-5/16 inch ball. You can also use this ball mount with a clevis, a lunette ring or a spade. You can pull the clip at the center of the shank and lift the pin up allowing you to hook up your trailer. And that will complete today's test fit for the Convert-a-Ball cushioned six-way multi-hitch ball mount for 2-inch hitches, part number CAV-6W on our 2013 Nissan Frontier. .
Installation: MaxxTow Tow Strap Loop for 2" Trailer Hitches on a 2013 Nissan Frontier
Today on our 2013 Nissan Frontier, we'll be test fitting the Maxxtow Tow Strap Loop for 2 inch hitches rated at 10,000 pounds part number MT70029. We'll begin our test fit by sliding the shank of the recovery loop into the opening of the hitch and securing it with the pin and clip which is sold separately. This heavy duty hitch mounted shackle provides an attachment point for strap, cable, or rope which is sold separately to be used in agricultural, industrial or recreational applications. It is made of a sturdy steel construction and has a corrosion resistant black powder coat finish. And that will complete today's test fit for the Maxxtow Tow Strap Loop for 2 inch hitches part number MT70029 on our 2013 Nissan Frontier. .
MaxxTow Adjustable-Height Ball Mount Review - 2013 Nissan Frontier
Today on our 2013 Nissan Frontier we'll be test fitting the Maxxtow adjustable height ball mount for 2-inch hitches with a 10-inch drop or 8-inch rise rated at 5,000 pounds, part number MT70067. Before we begin our test fit we'll firstly obtain the hitch height of our vehicle. This is the measurement from the ground to the inside top of the receiver tube. The hitch height for this vehicle is 17-1/4 inches. Keep in mind that this measurement may vary due to tire size, hitch style or after market accessories. We'll being our test fit in the drop position by sliding the shank of the ball mount into the opening of the hitch and securing it with the pin and clip. We can then remove the two pins here at the downward portion of the ball mount to adjust the ball mount platform to its lowest position. With the ball mount platform in its lowest position we can measure from the ground to the top of the ball platform getting a measurement of about 7-1/4 inches. We can now flip the ball mount over to the rise position and with the ball mount platform in its highest position we can again measure from the ground to the top of the ball platform getting a measurement of about 25-1/4 inches. Now, if your vehicle's hitch height matches our's, and your trailer's ride height is on or in between these two measurement in 1-inch increments, this should be an appropriate ball mount for you. That will complete today's test fit for the Maxxtow adjustable height ball mount for 2-inch hitches, part number MT70067, on our 2013 Nissan Frontier.
Setting up the MaxxTow Ball Mount w/ 2" Accessory Receiver on a 2013 Nissan Frontier
Today on our 2013 Nissan Frontier well be test fitting the MaxxTow ball mount with two inch accessory receiver for two inch hitches rated at 5,000lbs part #: MT70066. Before we begin our test fit well first need to obtain the hitch height of our vehicle. This is the measurement from the ground to the inside top of the receiver tube. The hitch height for this vehicle is 17 and a quarter inches. Keep in mind that this measurement may vary due to the tire size, hitch style or after-market accessories. Well begin our test fit by sliding the shank of the ball mount into the opening of the hitch and securing it with a pin and clip.
Fit Test: Draw-Tite Ball Mount for 2" Hitches on a 2013 Nissan Frontier
Today on our 2013 Nissan Frontier we'll be test fitting the Draw-Tite Ball Mount for the 3/4" rise or 2" drop rated at 7500 pounds, part number 2923. Before we begin our test fit we'll first need to obtain the hitch height of our vehicle which is the measurement from the ground to the inside top of the receiver tube. The hitch height for this vehicle is 17-1/4". Keep in mind that this measurement may vary due to tire size, hitch style or after market accessories. We'll now go ahead and slide shank of the ball mount in the drop position into the opening of the hitch and secure it with a pin and clip. We'll then measure from the ground to the top of the ball platform and we'll get a measurement of about 14-3/4". If your vehicle's hitch height matches ours and your trailer's ride height matches this measurement this should be an appropriate ball mount for you. We can now flip the ball mount over to the rise position.
Convert-A-Ball Pintle Mounting Bar Review - 2013 Nissan Frontier
Today on our 2013 Nissan Frontier we'll be test fitting the Convert-A-Ball Cushion Adjustable Pintle Mounting Bar for Two Inch Hitches Rated at 10,000 Pounds, part number ampc2. Before I began our test fit we'll first need to obtain the hitch height of our vehicle. This is the measurement from the ground to the inside top of the receiver tube. The hitch height for this vehicle is 17-1/4 inches. Keep in mind that this measurement may vary due to tire size, hitch style or after-market accessories. We'll now begin our test fit in the drop position by sliding the shank of the pintle mounting bar into the opening of the hitch and securing it with the pin and clip.
Install: Convert-A-Ball Dual-Cushioned, Adjustable Ball Mount on a 2013 Nissan Frontier
Today on our 2013 Nissan Frontier we'll be test fitting the Convert-A-Ball Dual Cushioned Adjustable Ball Mount with a seven inch rise or nine inch drop rated at five thousand pounds, part number CAB-UM. Before we begin our test fit we'll first need to obtain the hitch height of our vehicle. This is the measurement from the ground to the inside top of the receiver tube. The hitch height for this vehicle is seventeen and a quarter inches. Keep in mind that this measurement may vary due to tire size, hitch style, or after market accessories. We'll now begin our test fit in the drop position by sliding the shank of the ball mount into the opening of the hitch and securing it with the pin and clip. We can then measure from the ground to the top of the ball platform and we'll get a measurement of about six and three quarters inches.
Set up: Convert-A-Ball Ball Mount for 2" Hitches on a 2013 Nissan Frontier
Today on our 2013 Nissan Frontier, we'll be test fitting the Convert-A-Ball cushioned ball mount for 2 inch hitches, with a 6 3/4 inch rise, or 8 inch drop, rated at 10,000 pounds, part number AMSC8. Before we begin our test fit, we'll first need to obtain the hitch height of our vehicle. This is the measurement from the ground to the inside top of the receiver tube. The hitch height for this vehicle is 17 1/4 inches. Keep in mind that this measurement may vary due to tire size, hitch style, or after market accessories. We'll now begin our test fit in the drop position by sliding the shank of the ball mount into the opening of the hitch, and securing it with a pin and clip. With the ball mount secured, we can then measure from the ground to the top of the ball platform, getting a measurement of about 9 inches. If your vehicle's hitch height matches ours, and your trailer's ride height matches this measurement, this would be an appropriate ball mount for you. We can now flip the ball mount into the rise position, and again, measure from the ground to the top of the ball platform, getting a measurement of about 23 1/4 inches. Once again, if you trailer's ride height matches this measurement, this would be an appropriate ball mount for you. That will complete today's test fit for the Convert-A-Ball cushioned ball mount fro 2 inch hitches, part number AMSC8, on our 2013 Nissan Frontier.
2013 Nissan Frontier Convert-A-Ball Ball Mount for 2" Hitches: Complete Installation
Today on our 2013 Nissan Frontier, we'll be test fitting the Convert-A-Ball cushioned ball mount for 2 inch hitches, with a 1 inch rise, or a 2 inch drop, rated at 14,000 pounds, part number AMSC2HD. Before beginning our test fit, we'll first need to obtain the hitch height of our vehicle. This is the measurement from the ground to the inside top of the receiver tube. The hitch height for this vehicle is 17 1/4 inches. Keep in mind that this measurement may vary due to tire size, hitch style, or after market accessories. We'll now begin our test fit by sliding the shank of the ball mount, in the drop position, into the opening of the hitch, and securing it with the pin and clip. We can then measure from the ground to the top of the ball platform, getting a measurement of about 15 1/4 inches. If your vehicle's hitch height matches ours, and your trailer's ride height, which is the measurement from the ground to the bottom of your trailer's coupler, while your trailer is level, matches this measurement, this should be an appropriate ball mount for you. We can now flip the ball mount over into the rise position, and again, measure from the ground to the top of the ball platform.
DIY Install: Convert-A-Ball Ball Mount for 2" Hitches on your 2013 Nissan Frontier
Today on our 2013 Nissan Frontier, we'll be test fitting the Convert-A-Ball cushioned ball mount for 2 inch hitches, with a 3/4 inch rise, or a2 inch drop, rated at 10,000 pounds, part numberAMSC2. Before we begin our test fit, we'll first need to obtain the hitch height of our vehicle. This is the measurement from the ground to the inside top of the receiver tube. The hitch height for this vehicle is 17 1/4 inches. Keep in mind that this measurement may vary due to tire size, hitch style, or after market accessories. We'll begin our test fit by sliding the shank of the ball mount, in the drop position, into the opening of the hitch, and securing it with the pin and clip. We can then measure from the ground to the top of the ball platform, getting a measurement of about 15 inches. If your vehicle's hitch height matches ours, and you trailer's ride height matches this measurement, this would be an appropriate ball mount for you. We can now flip the ball mount over, into the rise position, and again, measure from the ground to the top of the ball platform. We'll get a measurement of about 17 1/2 inches.
Installing the Convert-A-Ball Ball Mount for 2" Hitches on your 2008 Nissan Frontier
Today, on our 2008 Nissan Frontier, we're going to be test-fitting the Convert-A-Ball Cushion Ball Mount, part number AMSC4. Now, the first thing we want to do is measure our hitch height. That's from the ground to the inside top of our receiver tube. Our Frontier has a hitch height measurement of 17 inches. Now, keep in mind that this measurement will vary some even within 2008 Frontiers. Variances in tires, exact model type, and aftermarket parts, even the hitch itself, will determine the hitch height, so make sure you measure your particular vehicle.
Set up: Draw-Tite Ball Mount for 2" Hitches on a 2008 Nissan Frontier
Today, on our 2008 Nissan Frontier, we'll be test-fitting the Draw Tite Ball Mount, part number 2923. Now, the first thing we want to do is measure our hitch height. That's from the ground to the inside top of our receiver tube. Our Frontier has a hitch height measurement of 17 inches. Now, keep in mind that this measurement will vary some even within 2008 Frontiers. Variances in tires, exact model type, and aftermarket parts, even the hitch itself, will determine the hitch height, so make sure you measure your particular vehicle.
Setting up the Curt Tri-Ball Mount on your 2008 Nissan Frontier
Today, on our 2008 Nissan Frontier, we'll be test-fitting the Curt Triball Mount Hollow Shank, part number C45001. Now, the first thing we want to do is measure our hitch height. That's from the ground to the inside top of our receiver tube. Our Frontier has a hitch height measurement of 17 inches. Now, keep in mind that this measurement will vary some even within 2008 Frontiers. Variances in tires, exact model type, and aftermarket parts, even the hitch itself, will determine the hitch height, so make sure you measure your particular vehicle.
Convert-A-Ball 6-Way Multi-Hitch Ball Mount Review - 2008 Nissan Frontier
Today, on our 2008 Nissan Frontier, we'll be test-fitting the Convertible Six-Way Multi Hitch Ball Mount, part number CAB-6W. This ball mount features six different towing methods. There are three ball sizes of 1 7/8, two-inch, and 2 5/16, and there is also the ability to use a Clevis lunette ring or spade hitch as well. Now, the first thing that we want to do is measure out hitch height. That's from the ground to the inside top of our receiver tube. Our Frontier has a hitch height measurement of 17 inches.
How to Install: Convert-A-Ball Ball Mount for 2" Hitches on your 2008 Nissan Frontier
Today, on our 2008 Nissan Frontier, we'll be test fitting the Convert-A-Ball Cushion Ball Mount, part number AMSC2. Now, the first thing we want to do is measure our hitch height. That's from the ground to the inside tab of our receiver tube. Our Frontier has a hitch height measurement of 17 inches. Now, keep in mind that this measurement will vary some even within 2008 Frontiers. Variances in tires, exact model type, and aftermarket parts, even the hitch itself, will determine the hitch height, so make sure you measure your particular vehicle.
What our customers are saying:
"Thanks for my order super fast shipping quality excellent. will order again. thanks again. A+A+A+ to deal with."