etrailer Ball Mount Kit for 2" Hitches - 3/4" Rise or 2" Drop - 7,500 lbs

See what our Experts say about this etrailer Trailer Hitch Ball Mount

• What is the Hitch Ball Size of a 2000 Coleman Sea Pine Pop-Up Camper
  I do not know for certain but my guess is that their 2000 Coleman Sea Pine Pop-Up Camper uses a 2" hitch ball. If you have access to the trailer then you can look at the top of the coupler as this will tell you what size hitch ball to use. The other option is a 1-7/8" hitch ball but again, there is no way to know for certain without looking at the trailer coupler. Depending on the rise/drop you need (see article) you could use the Ball Mount Kit part # 989891 which comes with both a 1-7/8"...
  view full answer...
• Availability of a 2 Inch Ball Mount with a 1 Inch Drop
  I do have a ball mount that will work for you but none of our ball mounts have exactly a 1" drop. However, a ball mount with a 2" drop will more than likely work for you as when you measure from the ground to the bottom of your trailer coupler while level in comparison to the distance from the ground to the top of the inside edge on your trailer receivers tube opening, the tongue weight of the trailer will then need to be applied to the vehicle which is raley taken into consideration. Depending...
  view full answer...
• Picking Out Ball Mount for Truck Hauling Rental Trailer
  If you want to make this as inexpensive as possible I would recommend calling the trailer rental place and first seeing if they have a ball mount they could just let you borrow when you rent the trailer as that is pretty common. Next option would be then to ask them what the distance is from the bottom of the coupler lip on their rental trailer down to the ground and compare that to the distance from the top of the hitch opening down to the ground. That difference would be the amount of...
  view full answer...
• Difference Between etrailer Ball Mount Kit # 989891 and # 989899
  The difference between the two ball mount kits # 989891 and # 989899 is just that the # 989899 comes with two of the ball mounts that comes with the # 989891 and an additional hitch pin and clip.
  view full answer...
• Best 4-way Flat Wiring for a 2022 Hyundai Palisade
  The 4-way wiring harness that I recommend for your 2022 Hyundai Palisade is going to be the T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # 118784. This is going to be one of the easier installations. The T-One connector plugs into your vehicle's wiring harness, which is located behind the driver's-side interior trim panel in your rear cargo area. Once installation is complete, the 4-way flat connector will be stowed in an out-of-the-way location within your cargo area....
  view full answer...
• etrailer.com Ball Mount Kit Compatibility with Draw-Tite Class III Trailer Hitch on a 2006 BMW X5
  The etrailer.com ball mount kit you referred to would likely be a great choice. Its compatibility would depend largely on the height of your trailer coupler when the trailer is level. You'll want to choose a ball mount with the proper height so the trailer is sitting level. To determine the correct height ball mount you'll need you'll need to measure the heights of the hitch and the coupler, then determine the height difference. The height difference will equal the rise or the drop you'll...
  view full answer...
• Will the Draw-Tite Trailer Hitch Part 24773 Fit on a 2006 Nissan Quest
  The Class III Draw-Tite # 75159, and the one I recommend, is one of trailer hitches that fit your 2006 Nissan Quest. It has a maximum tongue weight of 300 pounds and 3,500 pound towing capacity. It's easy to install and no drilling is required. The custom wiring is the Tow Ready # 118469 and if you need a ball mount, I would get the ball mount kit # 989891 which includes 1-7/8 inch and 2-inch hitch balls, ball mount with 3/4 inch rise or 2-inch drop, pin and clip and a handy storage bag. The...
  view full answer...
• Recommended Trailer Hitch And Wiring For 2015 Jeep Grand Cherokee
  If you are looking for a complete towing package for your 2015 Jeep Grand Cherokee, first I would start with the Draw-Tite Max-Frame Trailer Hitch Receiver # 75699 if you don't have the Diesel models. This hitch is a fully welded vehicle trailer hitch is strong and durable. Draw-Tite's Tested Tough guarantee ensures that this hitch exceeds industry standards. The combination of an e-coat base and a powder coat finish provides excellent rust protection. There is no drilling required for...
  view full answer...
• Recommendation For Wire Harness For 2012 Toyota RAV4
  The Draw-Tite Class III Max Frame Receiver Hitch, Item # 75235, is a confirmed fit for your 2012 Toyota RAV4 but wiring is not included. The Draw-Tite has a 2 inch hitch opening, a 4,500 lb total weight capacity, and a 675 lb tongue weight capacity. It has an easy, bolt-on installation and all the installation hardware is included. For a wiring harness, I recommend the T-One Vehicle Wiring Harness, Item # 118412, which is a confirmed fit for your RAV4. If you need a ball mount and hitch...
  view full answer...
• Recommended Trailer Hitch for a 2013 Ford Escape SE for use with a Hitch Bike Rack
  No drilling is necessary or trimming fascia on the Draw-Tite # 75758, and the instructions will be included or you can view the instruction links. I included installation videos for the hitch on a 2013 Ford Escape. You may need to use a burr bit or file to enlarge the access hole if needed. It's very easy and take a look at the video for the 2015 Ford Escape at the 2 minute 12 second mark. The Draw-Tite Class-III trailer hitch # 75758 has a 525 pound tongue weight and 3,500 pound towing...
  view full answer...
• Is etrailer Ball Mount Kit 989891 Matte Black Like Trailer Hitch e98850
  The etrailer Ball Mount Kit for 2" Hitches # 989891 does not have the same matte black powder coat finish as the etrailer Trailer Hitch Receiver # e98850. The ball mount is a bit glossier so they aren't a perfect match but it will be pretty difficult to tell the hitch and ball mount apart unless someone is really trying to find a difference. The ball mount kit is an exceptional value because it includes a ball mount with 3/4" rise or 2" drop, a pair of hitch balls (2" and 1-7/8"), a pin...
  view full answer...
  
• Trailer Hitch for 2019 Subaru Outback with Rear Sensors on Bumper
  I recommend going with the Draw-Tite # 76227 . This hitch has a 2" receiver that won't interfere with the backup sensors on your bumper. This hitch has a 600-lb TW / 4000-lb towing capacity to maximize the towing capabilities of your 2019 Subaru Outback wagon. I really like that this hitch has the concealed cross-tube design so that it has a virtually invisible footprint on your vehicle- very similar to the EcoHitch, but at a much better price point. You're going to have to remove the...
  view full answer...
• Does Curt 2" Trailer Hitch Fit With Stow&Go Seats on a 2010 Chrysler Town and Country
  Yes, the Curt Trailer Hitch Receiver # 13364 will still fit a 2010 Chrysler Town and Country even if it has the Stow&Go seats. We actually had the chance to install this hitch on the exact same style that you're talking about and I've attached an installation video for you to check out. A lot of people get a hitch installed on a Town and Country to haul smaller trailers. If this is you then you'll also need the wiring kit # 118552 and a ball mount kit like part # 989891 which includes...
  view full answer...
• Does Curt Hitch for 2014 Nissan Murano Come with Wiring and Can it be Installed Without a Lift
  Great questions! The Curt Trailer Hitch Receiver # 13577 just comes with the hitch itself. To add the corresponding wiring for your 2014 Nissan Murano SL you'll need the Curt # 55571 as well. I have attached installation videos for each that you can check out. As far as installing it without a lift goes, I sifted through the reviews on this hitch and it seems like other people were able to install it fairly easily without using a lift; some people even said they didn't need to lower the...
  view full answer...
  
• Towing Capacity for 2011 Subaru Forester With Draw-Tite Trailer Hitch Receiver
  I checked the owner's manual in regards to the towing capacity of your 2011 Subaru Forester, and it states that the maximum towing capacity is 1,000 lbs if the trailer does not have brakes or 2,400 lbs if the trailer does have brakes. So that is the maximum you can tow with your Forester and the Draw-Tite Trailer Hitch Receiver # 75650. Even though this hitch has a 4,000 lb capacity, you have to abide by the lowest-rated capacity when towing so either 1,000 lbs or 2,400 lbs depending on...
  view full answer...
• Does Installing the Draw-Tite 75586 on a 2013 Toyota Highlander SE Require Mud Guard Removal
  No. Installing a hitch like the Draw-Tite # 75586 does not require the removal of the mud flaps on your 2013 Toyota Highlander SE. This hitch installs without any drilling required but trimming or removal of underbody panel may be required for installation. If you're going to be towing with this hitch you'll also need a wiring harness, ball mount, hitch ball, hitch pin and clip. For wiring, I recommend using the Tekonsha T-One # 118449 because of the reliability of the powered converters...
  view full answer...
• 2015 Jeep Grand Cherokee Limited 6 Cylinder Receiver Hitch and Wiring Harness
  Yes, the Draw-Tite Max-Frame hitch receiver item # 75699 is a confirmed fit for your 2015 Jeep Grand Cherokee Limited 6 cylinder. The prices for each can be found on the product pages. The only models that that specific hitch does not fit are the SRT-8 and EcoDiesel SRT-8. I recommend the Tekonsha T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector item # 118727. It plugs into the Jeep's wiring adapters behind each tail light. I've linked an install video for you. I also recommend...
  view full answer...
• Recommended Trailer Towing Package for a 2014 Chevrolet Captiva Sport
  For a 2014 Chevrolet Captiva Sport, I recommend the Draw-Tite Max-Frame Trailer Hitch Receiver part # 75556. The Draw-Tite Max-Frame is a Class III trailer hitch with a 2" receiver tube opening. The hitch is rated for 400 lbs tongue weight (TW) and 4,000 lbs gross trailer weight (GTW). I have attached a review video of this hitch installed on a similar 2013 Chevrolet Captiva Sport for you as well. For a trailer wiring harness, I recommend using the Hopkins Plug-In Simple Vehicle Wiring...
  view full answer...
• Hitch for 2012 MB Sprinter 3500 with 170 Extended Wheelbase
  The Draw-Tite Max-Frame Trailer Hitch Receiver # 75549 fits a 2012 Mercedes-Benz Sprinter 3500 with the 170" wheelbase (and standard bumper) and as long as it does not have the 30-3/8" frame, measured outside to outside of frame. If you have the factory step bumper then you need the Draw-Tite Max-Frame Trailer Hitch Receiver # 75601 instead which has the same criteria for fitment. If you're looking to tow with the Sprinter then you need the T-One Wiring Kit # 118650 and a ball mount kit...
  view full answer...
• Will Draw-Tite Hitch Fit 2020 BMW X5 sDrive 40i
  Yes, the Draw-Tite Max-Frame Trailer Hitch Receiver # 76288 will fit your 2020 BMW X5 sDrive 40i. The reason why we specify "excluding M performance models" is because that option has a different trim package so it changes out the hitch interacts with the vehicle body. The sDrive has the same trim style as the xDrive which this hitch was installed on in the linked instructions (see attached). If you're looking to use this for towing a trailer then you also need a wiring kit and a ball...
  view full answer...
  
• Trailer Hitch Recommendation for a 2020 Chevy Traverse
  I recommend going with the Draw-Tite Max-Frame Trailer Hitch Receiver # 76184 for your 2020 Chevy Traverse. This hitch installs so that the receiver can be covered up with the trim piece when you aren't using it, and it also comes with a bracket for a wiring connector if you plan on doing some towing. Attached are a few photos of this hitch and some wiring installed as well as an installation video that you can reference. If you plan on using this for towing then I recommend the T-One...
  view full answer...
  
• Does Tekonsha T-One Wiring from 2017 Kia Sportage Fit a 2020 Kia Sportage
  Great question! Yes, the T-One Vehicle Wiring Harness # 118698 is compatible with your 2020 Kia Sportage. This kit fits a 2017-2020 Sportage so you're good to go. In all honesty if you checked a month or so ago it could very well have not been listed as a fit yet. Since your 2020 is a newer vehicle sometimes they are still figuring out what wiring fits what vehicle so Tekonsha may have just recently confirmed that the 118698 actually fits the 2020 model. If you don't already have a trailer...
  view full answer...
• Availability Of Ball Mount That Is Straight And Has A Single 1-7/8 Hitch Ball
  It sounds like you are looking for something similar to the Buyers Products Tri-Ball Hitch - Tubular Shank with Chrome Balls # 3371802207 that only has a 1-7/8" diameter hitch ball. The closest option we have to this is the etrailer Ball Mount Kit # 989891 which includes a ball mount that measure 8-1/2" from the center of the hitch pin hole to the center of the hitch ball hole, and is right around 12" long overall. Now this ball mount does not have 0" rise/drop, but has a 3/4" rise which...
  view full answer...
• Best Hitch For a 2021 Honda CR-V
  The hitch that I recommend for your 2021 Honda CR-V is the etrailer Trailer Hitch Receiver # e98848. This hitch will work with hybrid, non hybrid and touring models of the CR-V. It has a 2" receiver opening which is the most common size used for accessories such as bike racks, cargo carriers and ball mounts for towing a trailer. This hitch features a no drill installation and nice matte black finish that will help to hide any scratches. If you plan to do any towing and do not have a wiring...
  view full answer...

Do you have a question about this Trailer Hitch Ball Mount?