See what our Experts say about this Spectro Wiring

• How to Protect Wires From Squirrels
  Hey George! You can install the Replacement In-Line Fuse Holder for Curt Wiring Harness item # C58470-1on the 4-way wires of the Curt 4-Way Flat Trailer Connector with Circuit Protected Powered Tail Light Converter item # C85FV. This would be the only way we have to run fuses to that harness. To protect your trailer wiring, I recommend wrapping it with the Wire Loom 1/4" Diameter, 10' Long item # 7509-10. Other than running conduit I don't have another option to keep squirrels out of...
  view full answer...
• Will A Non-Powered Trailer Wire Harness Converter Still Allow Factory Light Signals Through
  Hey Kai, Plug-in wire harnesses like the Curt # C86CR would still allow the vehicle light signals through to the tail lights regardless if the converter was powered or not. I don't recommend connecting the power line to a separate 12v socket and turning the power on and off since it wasn't intended to be used in this way and could potentially cause issues/wear out the converter faster. Running the power line up to the battery is super easy to do it and if you're really worried about...
  view full answer...
• Recommended Wire Loom Size for Two 16 AWG Wires
  Troy, for just two 16 AWG wires you can use the Wire Loom 1/4" Diameter # 7509-10 you were looking at. It's the smallest loom we have so it will be a bit too big but will still work fine.
  view full answer...
• How Can I Keep the Wires Clean from GM Wired 5th Wheel Camera System to the Back of My Truck?
  Hello Robert, We don’t have a complete kit available for organizing the wiring, but I do have a few parts that can help you keep things neat and secure. For attaching the wiring along the trailer or truck frame, we offer the CE Smith Trailer Wiring Clips - Frame Mount - Zinc Plated Steel - Qty 10 # CE16867A. These are great for securing the cable to the frame, depending on how much slack you're working with. To protect the wiring from abrasion and the elements, I recommend using 1/4"...
  view full answer...
• How To Install a 7-Way Trailer Wiring Harness On a 2019 Subaru Ascent
  There are two different 7-way trailer wiring harnesses for a 2019 Subaru Ascent dependent on whether or not you have the factory tow package. If you do have the factory tow package then you should be using the Tekonsha OEM Replacement Vehicle Wiring Harness part # 118290, not the Universal Installation Kit for Trailer Brake Controller part # ETBC7. If you found a plug under the dash for the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers part # 3062-P then you have the factory...
  view full answer...
• Recommended Replacement Wiring And Lights For A Big Tex 35SA Utility Trailer
  Hey Jules, Big Tex doesn't list the part numbers for the lights used on the 35SA but it looks like the Optronics LED Combination Trailer Tail Light # STL3RB (driver side) and # STL2RB (passenger side) would be a match for the tail lights, but I'd still need to confirm dimensions with you. I'd also need dimensions on the clearance lights as well. For the wiring I recommend the Optronics Wishbone 4-Way Trailer Wiring Harness # A25W42B. This wishbone style harness will have two separate...
  view full answer...
• Is a Trailer Wiring Converter Needed for a 2011 Jeep Liberty
  Yes, a converter is needed for a 2011 Jeep Liberty because one the tail light circuits are on separate wires and they need to be combined for a trailer and two the factory tail light circuits are not sufficient to power the lights on a trailer as well as the lights on the vehicle. I recommend the T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector part # 118554 which has one of the most durable converters on the market due to the potting which helps keeps the wires attached...
  view full answer...
• What is the Best Size Wire Loom for Bonded 4 Wire and One 12 Gauge Wire
  I would go with a 3/8 inch diameter, like # 39035. That should provide enough space for the wires and still give good coverage. This loom comes in a 10 foot length. If you needed less of expect that you might have other wiring to run with the existing wires, you can go to a 1/2 inch loom, sold in 1 foot increments, # 459075-1.
  view full answer...
• Does The ThermaHeat RV Holding Tank Heater Pad Require Special Wiring
  You'd most likely be fine just using some # 16-1-1 with the standard casing but you could also get some wire with exterior rated jacketing if you wanted to go the extra step. You can also get some wire loom # 7509-10 and run it the length of the wires and use electrical tape to secure it. When installing the ThermaHeat RV Holding Tank or Step Heater Pad w/ Thermostat # 277-000164 you'll also want to use a switch like # 37212595 to be able to turn it off when not needed to avoid an unwanted...
  view full answer...
• Recommended Wire Gauge and Related Parts to Install 12V Battery Charge Line on 7-Way
  We recommend at minimum a 14-gauge wire for providing 12V charging power to a towed vehicle's battery, such as that included in the Roadmaster Battery Charge Line Kit for Towed Vehicles, item # RM-156-25. Naturally, a heavier-gauge wire would do better since it can deliver more current. If you prefer you can use 10-gauge wire # 10-1-1, a 40-amp auto-reset breaker like # PK54540, ring terminals # 44-5310A and wire loom # 7509-10 to make your own kit. You can avoid tripping the breaker...
  view full answer...
• Parts Needed to Install Always-On 12V Power Circuit on 2018 Ford Super Duty
  Ford did decide to change the operation of the 12V auxiliary power circuits on newer trucks. The fix for this annoying circumstance is easy enough. All you need to do is bypass the existing 12V circuit with a new direct battery connection that will allow the 7-way to have active 12V power at all times, regardless of the ignition key position or operation of the brake pedal. You will need just a few parts to accomplish this: circuit breaker # PK54540, 10-gauge wire # 10-1-1, ring terminals...
  view full answer...
• How Can Hot lead Wire Be Run When Installing Trailer Wiring Harness On 2016 Chevrolet Sonic
  Although we do not have a video showing the installation of the Curt T-Connector Vehicle Wiring Harness, part # C56303, on a Sonic, I have attached a helpful article that explains the different methods for running a hot lead wire to a vehicle battery. In most cases you can run the wire through a grommet to get the wire beneath the car. I understand running the power wire under the vehicle is not appealing but you can use wire loom like part # 7509-10 so the wire is protected under the...
  view full answer...
• Parts Needed For Running A High Capacity Charge Line To Trailer
  Yes, you will need to run a separate ground wire with the main power wire. So it would be best to use the Pollak 2-Pole Socket Connector # PK12801 with their 2-Pole Trailer Wiring Connector # PK12800 for your power wires. The physical connection from the ball mount will not work as an acceptable ground connection. I recommend using battery cable as a suitable cable for the power wires. If you need help determining the correct gauge for your length let me know how far the cable will be...
  view full answer...
• Can Wire Loom be Used to Protect Wiring from Sun Damage
  Wire loom like the # 7509-10 that you referenced is a great way to help protect wiring. This kit is 10 feet long and 1/4 inch in diameter. If you need bigger we have 1/2 inch diameter loom sold by the foot as part # 459075-1.
  view full answer...
• 4-Pole Wiring Harness Kits for 2016 Ford Transit T250 & T150
  The Curt # C56327 is a confirmed fit on both the 2016 Ford Transit T150 and T250 if they do not have the factory trailer wiring setup. This has custom-fit connectors that plug in at your taillight wiring; it has a white ground wire that will attach to the vehicle metalwork; and it has a single power wire that you will need to run up to the engine compartment to connect to the battery + terminal using the supplied fuse holder. The power wire for either kit can be run on the outside of...
  view full answer...
• Converting a 5 Pin Trailer Connector on a Motorcycle To a 4-way Flat on Trailer
  I have a solution for you, however we do not currently carry a vehicle 5-way to a trailer 4-way adapter. In order to connect your motorcycle to your trailer, you will want to create an adapter. To provide your trailer with a 4-way flat connector, you will want to use the Tow Ready Upgraded Circuit Protected Taillight Converter # 119178. The wires that come out of the harness's converter will be connected to a 5-way trailer connector. If the 5 pin on your motorcycle is round, you will...
  view full answer...
• Testing Trailer Brake Circuit and Replacing Brake Output Wire on 2013 Ford F-350
  Since your issue with the trailer brake circuit began with a big bump I would first check the wiring at the 7-way. That bump may have been a pothole but it could also have been a bit of road debris that may have damaged that wire. Essentially you'll want to inspect the truck wiring from the 7-way socket, forward as far as you can trace it. Look for damage to the insulation, cracks or worn spots. Look for points where the brake wire may be touching suspension components or any sharp edges...
  view full answer...
• Troubleshooting Trailer Wiring Harness That Instantly Blows Fuse When Connecting to Battery
  The Hopkins Plug-In Simple Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # HM11140395 having a spark as well as blowing a fuse is a sure sign that the ground is not connected properly or the power wire at some point is touching a metal ground. I recommend tracing that power wire to ensure there is no insulation missing where it could be touching metal. You can see with our installation of this wire we used wire loom # 7509-10 in some areas to assist with areas that have sharp...
  view full answer...
• Does Hot Lead Need to be Run to Battery on 2011 Subaru Impreza Wagon
  The type of battery you described is not something you will be able to use to install the Hopkins Plug-In Simple Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # HM11143894 on your 2011 Subaru Impreza Wagon You need to run a hot lead to the battery because this is the only way to ensure your car's wiring is not otherwise affected. To do this you may need Wire Loom, 10' Long # 7509-10 and Loom Clamp -1/4" # A0250. I have added a link to a help article on routing a power wire...
  view full answer...
• Availability of Solera Awning Wire Cover
  Hi Pat; we don't have a specific wiring cover for Solera awnings. If you can send me a picture of what you have I may be able to find an equivalent part. We do have wire loom like the # 7509-10 but I don't think that is what you're looking for.
  view full answer...
• Can a Trailer Be Pulled With a Faulty Breakaway System
  The trailer breakaway's are required in most states so I cannot advise for you to continue traveling without having the system repaired or replaced. It sounds like you have already identified the culprit (shorted wire) so what I recommend is just ordering a new system that way you can get it installed and hit the road again as soon as possible. The Pro Series Push to Test Breakaway Kit part # 50-85-315 is what I recommend for this because it is cost effective and easy to install. That said,...
  view full answer...
• Wireless and Wired Brake Controllers for 2019 Toyota Tundra with Factory 7-Way
  At this time (June 2019) we do not have any trailer brake controllers that offer under-dash plug-and-play installation in your 2019 Tundra with factory 7-way/4-pole. We do offer the no-wiring-needed Curt Echo controller # C51180 which requires only a working 7-way vehicle socket at the bumper and a compatible smartphone that serves as the display and control device. The Redarc Tow Pro Elite # RED44FR can be installed in your 2019 Tundra but it will need to be hardwired. If you refer to...
  view full answer...
  
• What Wiring to Use to Install Electric Trailer Brakes
  Trailer axles do sometimes include a wire for an electric trailer brake circuit to make it easier to route power to each of the brake assemblies. We have suitable 10-gauge brake circuit wiring, part # 10-1-1, that can be ordered by the foot. This wire has blue insulation which is the color usually associated with trailer brake wiring. Electric trailer brakes use a 2-wire hookup. Either wire from the brake can be used as ground or hot; since these wires are non-polarized it does not matter...
  view full answer...
• RV has 7 Way and Need to Connect 4 Way for Dolly and 4 Way for Tow Lights to Use at the Same Time
  I have a solution for you. We do not have any type of Y adapter but I do have the parts available to allow you to connect both 4 wire flat plugs at the same time. I do recommend that you first check to ensure that you will not be drawing too many amps on the circuit by using both the dolly wiring and the tow lights together. You will need the following products: Car and Trailer End Loop, # 9653P Qty 2 Pollack 7-Pole Trailer Connector, # PK12706 Qty 1 First you will start by cutting...
  view full answer...
  

Do you have a question about this Wiring?