2-Pole Socket Connector - Vehicle Side
(57 reviews)
Price: $38.98
In Stock
Pollak
Add to cart
2-Pole Socket Connector - Vehicle Side
Part Number: PK12801
In Stock
$38.98
Retail:$41.30
You Save: 6%
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
- All Info
- Reviews (57)
- Q & A (0)
- Videos (1)
- Photos
Pollak Trailer Wiring - PK12801
- Trailer Connectors
- Vehicle End Connector
- 2 Pole
- Plug Only
- Pollak
Pollak 2-Pole Socket Connector - Vehicle End
Features:
- Rated for 200 amps
- Will accommodate 4 or 6 gauge wires
12-801EP Pollak 2-Pole Socket Connector - Vehicle Side
Video of 2-Pole Socket Connector - Vehicle Side
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Video Transcript for The Low-Down on the 2-Pole Socket Connector
Today, we'll be reviewing part number PK12801. This is the Pollak 2-pole socket connector. This is rated for 200 amps, providing six to 24 volts. This will accommodate four or six gauge wires. It's going to be made from a cast aluminum construction. If you need a mounting bracket, you can purchase one separately, found on etrailer.com with part number PK11771. See here that the lid is a nice spring-loaded lid so it's always going to make sure that our connection points on the inside are protected from the elements.
Back here, the two connections, we have positive and negative so they're labeled on the outside. They're also going to be labeled on the inside. The holes are going to measure half an inch across by three-eights of an inch up and down. Each holes going to be identical. Those are going to be your mounting holes. That's going to do it for today's review of part number PK12801.
This is the Pollak 2-pole socket connector. .
Customer Satisfaction Score:
88% were satisfied with this product
12% of customers were not satisfied
- Wrong item was ordered
- Product did not meet expectations
Customer Reviews
2-Pole Socket Connector - Vehicle Side - PK12801
Average Customer Rating: 4.8 out of 5 stars (57 Customer Reviews)
Pollak 2-Pole Socket Connector - Vehicle Endby: Nathan06/25/2024
We mounted these on our fleets pickup trucks to allow us to hook a trailer mounted winch right into the truck battery easily. The product has been outside and used multiple times and shows no sign of wear or deterioration after 1 year. We are very pleased.
by: Howard05/31/2016
I am going to use this to power my new electric boat winch. I have not actually loaded my boat yet but in getting it all set up this plug will work perfectly. I made a mount that will hold both this plug and the 7 pin plug for the trailer. I was surprised as to how stout these plugs are, look like very good quality.
by: Mike 08/29/2023
This is a great product. I use it for powering my electric boat winch with the truck. No more carrying an additional battery for the winch.
When I put my Torquelift SuperTruss on, I have made an extension with this and have it on the end of the extension so I do not have to climb under the camper to hook up the power.
by: Nfannie07/06/2024
Excellent quality, really heavy duty. Exactly what we were looking for. It arrived a day early
by: Phillip 02/11/2021
product is great quality, very fast shipping. would highly recommend, will visit site when i need trailer parts.
by: no name03/08/2013
I've been looking for a connector for 2 4 ga wires for 9 mo. I know I'm not the only one trying to do this, I have ran into several people at stores looking for the same thing with no results. I found this one looks like it'll fit the bill for connecting my trailer to my tow vehicle with wiring large enough to actually charge the trailer battery. It came fast, and was all I had expected. I also bought the trailer side connection and the bracket to mount it with. Should be an awesome set up thanks to etrailer
by: Michael H09/01/2017
Good product. My only complaint is the spring that holds the door down is weak. The door is also the "catch" that retains the cord, so it needs to stay firmly against the top of the cord, and this one doesn't always do so.
by: Lloyd B05/04/2019
Used this product to transfer power to my fifth wheel
It was installed in the back of my 3500 ram beside the factory connector
by: Pete05/03/2019
Very good quality and heavy duty. Much better than plastic connector. Should last for years.
by: Larry B06/25/2017
Two pole connectors are difficult to find. etrailer had exactly what I needed.
by: Custom Vehicle Solutions08/22/2016
Pollak is my go to manufacturer for trailer electrical needs. The build affordable and robust items.
by: Gary S12/15/2017
Was a perfect replacement for the old burned out lights on my Featherlite stock trailer!!!
by: Guy B12/22/2014
Just what I needed to charge trailer batteries. Thanks
by: john arnold03/01/2012
i am disabled this was ordered to hook up lift and is what i planed to use it jn the installation of same
by: Harry J04/19/2013
Excellent quality connector. Good pric e.
by: Pete06/01/2016
Great service. Parts were as expected.
by: Forest01/23/2023
Kept me informed of shipping, back order information and everything else in a timely manner.
by: John03/15/2019
The parts are heavy duty and the service was quick.
John C.
3/16/2020
This plug is heavy duty and built well.
by: Paul11/18/2018
Very Good Company to do business with.. Item was shipped promptly and communication with them was one of the best! Item was just as advertised and priced the best that I had found online. Will be ordering again from them.
by: Daniel 12/19/2021
Daniel
12/20/2022
I was able to put connectors on my wires that easily attached to the posts on the back of this plug. It fits snugly and securely, preventing shorting out. I am pleased with the quality of this product.
by: Jim 04/18/2021
It works great, I have ordered another one
by: Steve03/06/2018
they are working as i expect them to with no problems.
by: Baili06/05/2018
Works good. Took a while for the part to arrive. Hopefully no one is in a big hurry to get it.
by: T. Wilson08/03/2017
Product was what I wanted and worked gr eat.
by: Michael06/03/2018
Well made socket, reasonably priced, but shipping is very slow!!!!
25
57
Show More Reviews
See what our Experts say about this Pollak Trailer Wiring
- How Does Pollack 2-Pole Connector # PK12801 Attach to WiresThe Pollack 2-Pole Connector # PK12801 is designed to have the wires attached with ring terminals. By crimping on ring terminals to the ends of the wires and then holding them on with the included screw.
view full answer...
- Comparing Pollak and Buyers Products 2-Pole Vehicle and Trailer ConnectorsThe Pollak 2-pole trailer and vehicle connectors # PK12800, and # PK12801 and Buyers products 2-pole trailer and vehicle end connectors # 337TC2012 and # 337TC1002 are very similar in quality, and there is not one that is clearly better than the other. I recommend just going with which ever one is the most cost effective at the time. I included videos of the products mentioned for you to take a look at.
view full answer... - Recommended Solar Panel Connection for Furrion Prewired Solar Connection on TrailerThe 2.5-Watt Solar Battery Charger # PTW2997 is a great option for your solar charging needs on the go. This product will not completely supply the needs of your Furrion camera system but can be used along with a battery to charge the battery so the battery can power the unit. I recommend the Redarc In-Vehicle BCDC Battery Charger - Dual Input - DC to DC - 12V/24V - 25 Amp # 331-BCDC1225D which will allow you to have power from a solar panel amplified and will amplify the trailer battery...
view full answer... - What is the Difference Between the Pollak and Buyers Products 2-Pole Socket ConnectorsThe only difference between the Buyers Products 2-Way Die-Cast Zinc Trailer Connector # 337TC1002 and the Pollak 2-Pole Socket Connector # PK12801 is the brand. Aside from that these are interchangeable. They even fit the same mounting bracket # PK11771.
view full answer... - Does the 2-Pole Trailer Wiring Connector # PK12800 Solder or Use TerminalsI spoke with my contact at Pollak and he informed me that this 2-Pole Trailer Connector is designed to be soldered to 4-6 gauge wire. In order to accomplish that you will need to take the unit apart and remove each terminal from the plastic housing and solder each of the connectors individually. You may also be interested in a 2-Pole Socket Connector, part # PK12801.
view full answer... - Where Should Redarc In-Vehicle Battery Charger be Grounded?When wiring the Redarc In-Vehicle BCDC Battery Charger # 331-BCDC1240D along with connectors # PK12801 and # PK12800 you will want to ground to the tow vehicle chassis. The linked instructions specifically state that "all ground points must be connected to chassis earth". You can see this in the diagram I've added for you to take a look at.
view full answer...
- What Gauge Wire Should be Used with Vehicle Side 2-Pole Socket Connector # PK12801The 2-Pole Socket Connector - Vehicle Side, # PK12801, will accept 4 or 6 gauge wire so it should be no problem for your application. If you also need a mounting bracket, use # PK11771. For the matching trailer end connector, if needed, use # PK12800.
view full answer... - Is 2-Pole Socket Connector # PK12801 Water ProofThe 2-Pole Socket Connector # PK12801 that you referenced would be internally waterproof but uses exposed terminals so it's not ideal for applications where it would get submerged but in standard outside applications it would do fine exposed to most weather.
view full answer... - Can Wiring be Soldered to the Back of the Pollack 2-Pole Vehicle Side Trailer ConnectorThe Pollack 2-Pole Connector, # PK12801, is designed to have the wires attached with ring terminals. By crimping on ring terminals to the ends of the wires and then holding them on with the included screw, it will provide a strong and quick attachment method. The last picture on the product page shows a clear view of the back where the wires attach. This connector is the vehicle side. If you also need the matching trailer side, it is # PK12800.
view full answer... - Parts Needed For Running A High Capacity Charge Line To Trailer Yes, you will need to run a separate ground wire with the main power wire. So it would be best to use the Pollak 2-Pole Socket Connector # PK12801 with their 2-Pole Trailer Wiring Connector # PK12800 for your power wires. The physical connection from the ball mount will not work as an acceptable ground connection. I recommend using battery cable as a suitable cable for the power wires. If you need help determining the correct gauge for your length let me know how far the cable will be...
view full answer... - Will the 7-Pole Rubber Socket Boot Fit on the Heavy-Duty, 7-Pole, Round Pin Trailer Wiring SocketYes, the 7-Pole Rubber Socket Boot, # PK11761, works with 3 of the Pollak heavy duty wiring sockets that we carry. You can use it with part # PK11720 that you mentioned and it can also be used with part # PK12801 and # PK11851. The hole in the back of the boot is just under 7/16 inch and measures .425 with a dial caliper. I produced a short video showing how the boot fits on each item for you.
view full answer... - How to Shield the 2-Pole Socket Connector # PK12801 From the ElementsThere is not a boot or shield to protect this 2-Pole Socket Connector, part # PK12801, from exposure to elements. I would recommend a generous amount of Electrical Tape, part # BT66, to wrap the terminals and wires to keep out the elements. You may also be interested in purchasing a 2-Pole Trailer Wiring Connector, part # PK12800.
view full answer... - What Are the Dimensions of the Pollack 12801 2-Pole Socket ConnectorThe # PK12801 has the following dimensions: Top to Bottom: 3-5/8" Side to side: 3-3/4" Cut out: 1-13/16" I've also added a diagram with these dimensions for you to check out.
view full answer...
- Pollack Single Wire Socket # PK11851The # PK11851 Single Pole Round Pin Trailer Connector is designed to deliver power to a trailer. It's not grounded, because the battery on the tow vehicle is already grounded and trailer mounted equipment is usually grounded as well. The ground connection would typically be carried through an additional connector; depending on the piece of equipment you are supplying power to you might need to increase the ground wire gauge. If you need the connector to power a winch, you would be better...
view full answer... - Recommended Solar Panel and Charging Connection for Vilano 320GK with Prewire Furrion Solar InputThe Furrion Solar port # FSPINS-BS only fits with the male connector that comes on their solar suitcase. We had issues with that product so we don't carry it and they don't have a connector available as a separate part. I reached out to them directly to confirm this. The best solar panel in my opinion we carry for cost to function is the Go Power Portable Solar Kit w/ Digital Solar Controller # 34282730 and then you can simply use the 7-Pin Trailer Adapter for Go Power Portable Solar Kit...
view full answer... - 2 Pole Wiring Connector Recommendations for Powering Winch on TrailerThat would be a great idea. We don't carry 4 gauge wire, but the # PK12801 2-pole connector would work great for what you are trying to do. For the male connector you would want the part # PK12800. The connectors are rated for up to 200 amps so you will need to make sure your winch doesn't draw more than that.
view full answer... - Correct Ring Terminals For Connecting 6 Gauge Wire To Pollak 2-Pole Connector PK12801We sure do! The ring terminal you will need to connect your 6 gauge wire to the 2-Pole Socket Connector # PK12801 is the Spectro Ring Terminal - 6 Gauge - 3/8" Ring ID - Copper - Zinc Plated - Qty 1 # SWC57016Z. Now to crimp this heavy duty ring terminal on you will need a heavy duty crimper. I recommend the Deka Hammer Crimper # DW05410 which will have no issues crimping a terminal this size. Lastly I recommend adding heat shrink # DW05402 to the terminal to protect it from the elements. I...
view full answer... - Trailer Plugs Compatible with 1 and 2 Pole Pollak Trailer SocketsBoth trailer connectors you speak of are sockets that would typically be used on the vehicle end of the trailer/vehicle connection. One is a one pole, the other a two pole so they wouldn't be compatible with each other. The Pollak # PK11851 is a single pole wiring socket, which would be compatible with a # PK11852 single pole plug The Pollak # PK12801 2-pole socket would be compatible with a 2-pole plug, part # PK12800.
view full answer... - Recommended Solar Panel Connector to Replace Factory Furrion Solar Input on TrailerWe do not carry the solar connector as Furrion does not make them outside of their pricy briefcase solar panel. My recommendation is to change the ends of both connections to make compatible ends. I recommend the 2-Pole Socket Connector - Vehicle Side # PK12801 which doesn't require any soldering and the 2-Pole Trailer Wiring Connector - Trailer Side # PK12800 which again does not require soldering.
view full answer... - 2-Pole Male and Female Connector Needed for a Powerwinch RC30 Boat Trailer WinchThe Pollak 2-Pole Trailer Side Connector, # PK12800, and the Pollak 2-Pole Vehicle Side Connector, # PK12801, are made for each other and they would be excellent connectors for your Powerwinch RC30 trailer winch. If it is possible, I would recommend running 8 gauge wire because it will provide less resistance on the circuit and electric winches typically require thicker gauge wire. These are zinc die-cast connectors that are very durable. They are commonly used in heavy-duty applications...
view full answer... - Availability of a Mounting Bracket Compatible with 2-Pole Socket Trailer Connector # PK12801The 2-Pole Socket Connector - Vehicle Side, # PK12801, is housed in its own mounting bracket it you need to mount it flush against a surface. But, if a bracket is needed, you can use Pollak Bracket, # PK11771. I went out to the warehouse and pulled both parts and the mounting holes line up and the connector fits in the bracket opening. You may also be interested in the trailer side that is compatible, the 2-Pole Trailer Wiring Connector - Trailer Side, # PK12800.
view full answer... - Could Pollak 2-Way Connectors be Used for Fuel PumpYes you could use the 2-way connector part # PK12800 with the # PK12801 for a gas pump like you mentioned.
view full answer... - 2 Pole Connector for Powering Trailer Battery and Trailer LiftgateYou don't have to use an isolator if you don't need one. If your plan is to unplug the trailer when not in use there would be no need to use an isolator. For a 2 pole socket for your vehicle we have the part # PK12801 and then for the trailer side we have the part # PK12800 which would be a great solution. I wish we had a fairlead or roller solution for your winch cable but at this time we do not.
view full answer...
- Does the Pollak Single-Pole Trailer Connector Provide a Ground ConnectionThe # PK11851 Single Pole Round Pin Trailer Connector is designed to deliver power to a trailer. It is not grounded, as the battery on the tow vehicle is already grounded and trailer mounted equipment is typically grounded as well. The ground connection would typically be carried through an additional connector, depending on the piece of equipment you are supplying power to you might need to increase the ground wire gauge. If you need the connector to power a winch, you would be better...
view full answer...
Do you have a question about this Trailer Wiring?
Info for this part was:
Expert Research:
Michael H
Expert Research:
Jeff D
Expert Research:
Jameson C
Installed by:
Cole B
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Product Experts Available Now!
Call 1-800-940-8924
Phillip
2/12/2022
quality product still excellent working condition.