Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
This compact 1" diameter light delivers strong, clear illumination while drawing just 0.06 – 0.08 amps at 12 V DC. The single red diode is energy-efficient and rated for up to 100,000 hours of operation, so you can count on it for lasting performance with minimal power draw. The clear lens over the red LED keeps the light sharp and visible without being harsh, even after years of use.
Built for harsh conditions, the sealed polycarbonate housing and UV-resistant lens are fused into one waterproof unit. The circuit board is fully protected with TecSeal urethane potting that outperforms common epoxy potting, keeping moisture and dust from ever reaching the electronics. With its IP68 rating, it’s ready for anything from rainy roads to full submersion during boat launches.
Tight on space? This light fits neatly into a 3/4" diameter cutout using the included grommet for a clean, recessed mount. At only 7/8" thick, it stays out of the way while giving your trailer a factory-grade look. The 9" pigtail with 0.156" bullet connectors plugs directly into matching wiring—no extra adapters or hardware needed.
For setups where every inch of visibility counts, this PC-rated light shines across a full 180-degree arc. That wide beam lets a single unit serve as both a clearance and side marker light when mounted at the right angle, simplifying installation while keeping your trailer clearly visible from multiple directions.
The internal circuit board uses military-grade construction and urethane potting for maximum durability against vibration and wear. It meets or exceeds FMVSS 108 standards, ensuring reliable brightness and safety compliance mile after mile. It’s a small light built with serious hardware behind it.


Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Hello, everybody. This is Jeff at etrailer.com. Today we're gonna take a look at this TecNiq Recessed Mount Mini Red LED Clearance Side Marker Light with the Grommet. Now, this is a very small one inch round LED light that'll serve as a rear side marker and clearance light on your trailer. And it is a PC rated light. It'll a produce 180 degree arc of red light to indicate the position of your trailer.
It's in a sealed waterproof unit that'll include durable polycarbonate housing and a UV-resistant lens. It is a military grade construction of the circuit board. Offers you urethane potting, which is better protection than the common epoxy potting. And the LED they use as a premium LED. It is energy efficient, long lasting, and vibration resistant.
The LED is rated for up to a hundred thousand hours of operation. Now, I do have this hook to some 12 volt power, just so I can show you the light and the color of it. So what I'm gonna do is go ahead and turn on the 12 volt power, and you can see, the light comes on. It is a red LED. We'll go ahead and turn it off.
And it's a clear lens that's over the red LED. It is compatible with the 12 volt DC system. And there you can see how bright it is and the red it gives off. We'll go ahead and turn back on overhead light. Turn off our power.
Disconnect everything. Now, it is a recessed mount installation. As you can see, it comes with the included rubber grommet, and it does require a three quarter inch diameter cutout for this light to fit into. You'll notice on the other end it uses bullet connectors, which will plug into your trailer's matching connectors. Total wire length on this is about nine inches. Now, this will meet or exceed the Federal Motor Vehicle Safety Standards 108 Standards. Few specs on this. The overall diameter of the light itself is one inch. Thickness is about seven eights of an inch. And the dimensions, without the grommet, is three quarters of an inch, and also seven eights of an inch. Input voltage for this light is nine volts to 14 volts. And the power draws only 0.06 to 0.08 amps. But that should do it for the review on this TecNiq Recessed Mount Mini Red LED Clearance Side Marker Light with the Grommet.
Ratings & Reviews

Nick S.
12/1/2025
That is great to hear! I am glad the process was easy and I hope the install was as well. It looks great on your vehicle!

Mike L.
2/18/2026
The pigtail wires are 16-gauge which is typical. Hope that helps!!
Info for this part was:
At etrailer we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.






Mike L.
4/30/2026
We're glad to hear that, good job!