Arrives before Christmas 
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
1-1/2" Diameter round. Waterproof, incandescent trailer light with illuminates your trailer's license plate. Durable chrome-plated steel housing. Snap-in design secures into 1-1/4" diameter cutout. 1-Wire design. (1) 168 bulb.
Features:
Specs:
Manufacturer Cross Reference
Light will work as an exact replacement for:
Grote # 60101
Truck Lite # 26391C and 26393C
Optronics # LP11CB
The waterproof construction of this light makes it ideal for use on trailers that may be submerged, like a boat trailer. The circuit board is sealed, which means that water will not damage the diodes or circuit board.
California residents: click here
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Take a look at the Peterson Sealed Chrome Snap-In License Plate or Utility Light. This is a chrome-plated steel lite that'll snap into a 1-1/4-inch diameter hole. It's commonly used to illuminate a license plate on step bumpers, does require two units for legal license illumination, but it can also be used as a interior light, compartment light, courtesy light, or general illumination utility light. Does have a 5-1/2-inch wire lead. It's a black wire for power. Then, when you do snap this in, it snaps into a metal surface, so that's the ground.
I am going to hook this up at the end of the video just to show you how that works and how it lights up.Give the overall diameter on the light itself. From edge to edge, it's going to be right at 1-1/2 inches. Total depth from the very front of the light to the very back, it's right at 2 inches. Again, the design, you can see here, it'll snap into a 1-1/4-inch diameter hole.What we're going to do now is I got some 12-volt power here. We'll go ahead and hook the wire up, and you can see we're going to hook the power to the black wire, and then we're going to take the ground and hook it to one of these snap-in clips.
That's what'll go into the metal surface when you install it. Then, we'll go ahead and turn the power on, and you can see with it on, it lights it up. I'll go ahead and turn off the overhead lights, and you can see, gives you a nice, bright light to light up your license plate, and then we'll go turn back on the overhead lights, disconnect the power.That should do it for the review on the Peterson Sealed Chrome Snap-In License Plate or Utility Light.
Average Customer Rating: 4.8 out of 5 stars (16 Customer Reviews)
1-1/2" Diameter round. Waterproof, incandescent trailer light with illuminates your trailer's license plate. Durable chrome-plated steel housing. Snap-in design secures into 1-1/4" diameter cutout. 1-Wire design. (1) 168 bulb.Perfect match for the tail lights on our '96 Coleman tent trailer by Fleetwood.
This license plate light works perfectly for my 1985 Toyota Long-bed Pickup bumper. Every few years I need to replace the left- or right-hand light. These lights fit perfectly in the existing hole so the install takes just 10 minutes or so. It would be optimum if the length of wire was a bit longer but that is a very small issue. The performance of the light so far is outstanding.
Not a lot of light output. Very average.
Perfect replacement product !
Great product.Arrived fast and exact fit.Still works and looks great after one year.
Excellent fit and product workmanship.
Perfect fit for my 91 GMC Sierra. Shipped and arrived earlier than expected!
Excellent product. Excellent customer s ervice…..
Perfect fit. Great service as always.
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Steven M.
10/17/2021
Still looks and works great.I highly recommend these lights.