Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
This 4-1/4" Peterson LumenX round light handles brake, tail, and turn signals in one clean setup. With nine LEDs under a red lens, it shines strong when braking or turning and glows steady for tail illumination. The LED design runs cooler, lasts longer, and uses less power than old incandescent bulbs—perfect for keeping your lighting system efficient and dependable on 12V or 24V DC setups.
Wet conditions can ruin trailer lights fast, but this one is built to stay sealed tight. The skirted weld joint adds an extra layer of protection against water intrusion so moisture won’t get in to corrode the diodes or wiring. Whether you’re on wet roads or parked in the rain, the light’s construction helps keep it working like new.
Installing this light is straightforward. It fits into a recessed grommet mount (426-18 – sold separately) and connects with a standard 3-prong plug using a PL-3 pigtail adapter (421-491 or 431-491 – sold separately). Once installed, the setup sits flush for a clean finish that stays protected from snags or bumps.

Safety standards matter when it comes to lighting. This Peterson LED meets DOT and FMVSS 108 requirements for brake, tail, and turn signals, so it checks all the boxes for road use. It’s designed to last with 9V–32V DC input flexibility and comes backed by a 10-year limited warranty for peace of mind every time you hook up your trailer.

Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Today we're going to be taking a look at and showing you how to install the Peterson-Lumenx LED Trailer Tail Light. This light's going to give us all our necessary functions like our running lights. Our turn signals and our brake lights. As you can see these LED's are really going to put off a lot of light. Not only help keep you safe but other passengers on the road as well.Now what sets this light apart from any of the others is that it's LED. Those LED's are going to last a lot longer, they're going to be more reliable because you don't have to worry about any brittle filaments like tour traditional incandescent light has.
And because of that there will be a great upgrade from your traditional style incandescence's. They also use less power to work.Now each light is going to have nine diodes and something else that's going to set this apart from other lights is not only it is compatible with 12 volts systems but also 24 volt systems. The light does not come with the plug so depending on which style plug your trailer has already you may or may not have to buy a new one to work with the light. If you need one you can find it on eTrailer.com.All right, here on the back of the light we have our connection points. They do come with dielectric grease already on the contacts.
That way we don't have to worry about it during our install. And there's also raised letter on the back which tells you what each contact point is for. I'll give you a couple of measurements to make sure this will work with your application.The light is 4 1/4" wide and as far as the depth, from here to the end of the plug is 1 11/16" of an inch. Now I'll show you how easy it is to get these lights installed. They are designed to be used with a rubber grommet.
Since we're replacing ours, we're just going to go ahead and put in a new grommet while we're doing that. If you need a new one, or a replacement, you can find one on eTrailer.com.Now I'll show you how easy it is to get this light installed. First we'll take our wiring and feed it through the hole and just plug it into the back of the light. Now all we have to do is push the light into the grommet. These can be a tight fit so if you need to use some spray silicone lubricant or even some soapy water to help you out you can go ahead and do that now and then it will pop right into place.All right, now we can go ahead and put power to the light and make sure all the functions work properly.
Here we have our tail lights, our turn signal, and our brake lights. And that will do it for our look at and installation of the Peterson-Lumenx LED Trailer Tail Light.
Customer Satisfaction Score:
98% were satisfied with this product
2% of customers were not satisfied
Ratings & Reviews

Katrina B.
5/13/2023
Yikes, lets get you over to our customer service department for them to assist you.

Ryan
1/25/2026
Lights work great and look good! Hopefully i dont have to order more anytime soon but if i do, ill definitely buy from etrailer again!
Info for this part was:
At etrailer we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.








Ryan
4/3/2026
After a year, these dual voltage lights are working as good as the day I installed them for my customer