Arrives before Christmas To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
Quickly and easily install a 4-way trailer connector on your vehicle with this custom harness. T-connector plugs directly into existing wiring. Powered converter reduces strain on wiring system and is made using SMT to ensure superior performance.
Features:
Specs:
Installation
This custom-fit T-connector plugs into your vehicle's wiring harness, which is located in the rear cargo area. You will have to remove the trunk floor coverings, storage trays, scuff panel, and interior felt liner to access this harness. Once you've plugged in the T-connector, run the hot lead up to your car battery. Connect the lead to the included fuse holder, and then connect the fuse holder to the positive terminal on your battery.
Once installation is complete, the 4-way connector will be stowed in an out-of-the-way location within your cargo area.
It is recommended that you use a small amount of grease on all electrical connections - the plugs on your automobile and the 4-pole connector itself - to help prevent corrosion.
A tail light converter is built into this T-connector. This converter is a circuit-protected, battery-powered unit that bypasses the electrical routes that are used by a basic wiring harness. As a result, there is virtually no draw on your tail light circuits.
Because most trailers run on a two-wire system - wherein the brake and turn signals are carried on one wire - the separate brake and turn signals from your vehicle's three-wire system need to be combined so they are compatible with the wiring system of the trailer. This converter combines the brake and turn signal functions of your automobile so that they run on one wire to properly activate your trailer's tail lights. Note: This will not affect how the tail lights on your vehicle operate.
Curt builds each tail light converter using surface-mount technology (SMT). This method of construction involves soldering electronic components directly to the surface of a printed circuit board. SMT eliminates the need for leads, which are used in older through-hole technology. The result is a circuit board that is smaller yet provides more routing area and that offers superior performance, reliability and durability.
Circuit boards constructed using SMT have been shown to perform better under rough conditions with excessive vibration than those made using the through-hole method. And where would vibration be more likely to occur than in towing applications? Curt converters also produce less heat, leading to increased durability and longer life. In addition, lower levels of resistance ensure better performance, especially for parts that operate at higher frequencies.
Each Curt circuit board is made using high-quality components that are pieced together in the most technologically savvy fashion, leading to greater predictability and reliability in functioning.
California residents: click here
Easy time install. Working as advertised. Time will tell on durability. Purchased via phone order. The staff at etrailer were knowledgeable and professional. Thanks!!
I am very satisfied with this item. I had it professionally installed. It's the second wiring harness I've purchased from you; the first was for my other vehicle. I would buy from you again!
Cannot imagine adding trailer wiring to car without this kit. Definitely plug-and-play. The hardest part was running the wire underneath the car, from the trunk to the battery. No doubt much easier if you have a lift, but difficult using jacks or ramps.
This wiring kit ade the install extremely easy and is holding up very well. The trailer sits outside, uncovered year long and the wiring and lights still look almost new.
Easy to install. Works great!
perfect fit easy installation
Thanks to Bill E who looked into why I received a wrong type of wire harness (Hopkins instead of Curt) two times and corrected it to the right order, I will make it to my home in Florida from Iowa in the nick of time. I received all that I needed, including an adapter converting the wiring to trailer. Went from bad to "All is good"
Mark
Loved both products I purchased. Light kit and Curt trailer hitch for my 2018 Sonata. Both were extremely easy to install and built with quality materials. I will definitely purchase from etrailer again and I will also recommend to friends. Thank you!
Wire harness is still functional with no issues after a year.
The complete process from ordering to installing was a breeze.
Do you have a question about this Custom Fit Vehicle Wiring?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.