Square Drop Leg Stabilizer Jack Tube and Pin Hole Diameters
Updated 09/12/2025 | Published 08/16/2025
Question:
Re:Square Leg Stabilizer Jack p/n SJ-R208 interested in this product. Is the size of the leg 1 x 1? Size of the holes in the leg? Any info you can provide will be greatly appreciated.
asked by: D. W
0
Expert Reply:
Hey D, thank so for reaching out!
The Square Drop Leg Stabilizer Jack # SJ-R208 measures 1-1/4" for the tubing on the leg, and it has 7/16" diameter pin holes for the height adjustment. Those holes are also spaced 1-3/16" apart on centers if that helps at all.
What do you plan on using this for?
expert reply by:
Jon G
0
Pin Hole and Tube Diameter Measurements for Stabilizer Leg
(click to enlarge)
(click to enlarge)
Product Page this Question was Asked From
Square Drop Leg Stabilizer Jack - 18" Travel - 2,000 lbs - Qty 1
- Camper Jacks
- Pop Up Camper
- Teardrop Camper
- Travel Trailer
- Stabilizer Jacks
- Steel
- 1001 - 2000 lbs
- Manual Jack
- 18 Inch Lift
- Weld-On
- 1 Jack
- etrailer
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Shop: etrailer RapidRamps 6' Long Bolt-On Trailer Ramps for over 6-1/2' Wide Trailers
- Search Results: center cap
- Search Results: mud flaps
- Search Results: bearing 3984 trailer bearings races seals caps
- Search Results: battery maintainer
- Search Results: drop leg jack
- Search Results: accessories and parts
- Search Results: square drop leg stabilizer jack
- Shop: 3-Leaf Double-Eye Spring for 4,000-lb Trailer Axles - 25-1/4" Long
- Shop: Square Drop Leg Stabilizer Jack - 18" Travel - 2,000 lbs - Qty 1
- Shop: Optronics LED Trailer Light - Brake, Tail, Turn - Submersible - Round - Red
- Shop: 2-1/2" Round Trailer Clearance and Side Marker Light, Surface Mount - Red
- Shop: Piranha LED Clearance or Side Marker Trailer Light - Submersible - 3 Diodes - Round - Red Lens
- Shop: Square Direct Weld Jack w/ Footplate - Drop Leg - Topwind - 28-3/4" Lift - 7,000 lbs
- Video: Ultimate Overview of the Replacement Drop Leg for Bulldog Square Trailer Jacks
- Video: etrailer Trailer Jack TJD-7000-FT Review
- Video: Comprehensive Review: Square Drop Leg Stabilizer Jack
- Video: Replacement Drop Leg for etrailer and Ram Square Direct Weld Jacks Review
- Q&A: What is Overall Height of etrailer Jack # e34RV When Fully Retracted
- Q&A: What are the Dimensions of the Mounting Bracket on the Patriot Hitches Square Trailer Jack?
- Q&A: What is Minimum and Max of MORryde I-Beam Stabilizer Height
- Article: Trailer Lighting Requirements
- Q&A: Timbren SES for 2021 Nissan Frontier Hauling Commercial Mower and Towing Utility Trailer
- Q&A: What Drum do I Need to Replace My Lippert Drum with 696690 Stamped on it?
- Q&A: Can Spacers Be Added to Timbren SES To Make Smaller Gap
- Q&A: Will The B&W Anti-Rattle Clamp BW45FR Work With The Tow & Stow Ball Mounts?
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: How to Tell the Weight Rating of a Trailer Axle
- Article: 5 Things to Know About Weight Distribution Hitches
Jon G.
9/12/2025
Hey D, did the Square Drop Leg Stabilizer Jack work out for your needs? I'm asking because your experience could help others make informed decisions.