Yates Keel Roller for Boat Trailers - TPR - 10" Long - 5/8" Shaft

See what our Experts say about this Yates Rubber Boat Trailer Parts

• Fifth Wheel Hitch Recommendation for 2015 GMC Sierra 2500 Short Bed with B and W Gooseneck
  The # CAB-C5G1216 will work well with your Mor/Ryde pin box without an adapter of any type. The problem though is that this does not typically give enough offset to allow a short bed truck additional turning clearance since the offset swivels when the trailer turns. What gooseneck hitch do you have installed in the bed of your truck?
  view full answer...
• Looking for 10 Inch Keel Roller w/ Bushing that Runs All the Way Through
  The 10 inch keel rollers from Yates Rubber, like part # YR10000 have a bushing on either end and a metal tube in the middle that acts like a bushing. The # 811 simply has the plastic caps at each end. I'd recommend the # YR1000B from Yates. The non-marking roller is soft like polyurethane but is stronger than rubber. The roller has bushings on either end and a metal tube running through the roller that acts like a bushing.
  view full answer...
• How to Identify Replacement Bearings & Seals for Magic Tilt Boat Trailer
  The best way to confirm the correct replacement wheel bearings and seals for your 1999 Magic Tilt boat trailer is to pull one of the hubs and note the inner and outer bearing numbers and seal number. You can then directly search on those part numbers to find replacements. Trailer makers do alternate parts sometimes so even if you have the owner's manual and it says the trailer uses bearings X and Y, they may not be what is in the hubs. It is always best to check the existing parts. We...
  view full answer...
  
• Best 10" Keel Roller for Boat Trailers
  The Yates Keel Roller for Boat Trailers part # YR1000Y is what I recommend as our best 10" roller. This roller is made of a thermal-plasticized rubber so it's stronger than standard rubber and non-marring. It's also made here in the USA.
  view full answer...
• Roller Shaft for 10 Inch Boat Trailer Keel Roller
  All the roller shafts we offer are constructed of zinc plated steel. Unfortunately, we don't offer any in stainless. The Yates Rubber # YR1000Y 10 inch keel roller you'd looked at would typically use an 11 x 5/8 inch shaft like the # CE10726A which includes the pal nuts. The roller would typically be mounted to the boat trailer using a panel bracket like part # CE10304G.
  view full answer...
• Does The Yates Keel Roller YR1000Y & YR1000B Come With Brackets?
  Both the Yates Keel Roller for Boat Trailers - TPR - 10" Long - 5/8" Shaft Item # YR1000Y and the Yates Keel Roller for Boat Trailers - TPR - 10" Long - 5/8" Shaft - Blue Item # YR1000B are replacement rollers. Each roller is a different size so depending on what bracket you have currently. So these rollers do not come with the brackets. These are both designed for a 10" wide bracket with 5/8" diameter shaft. Here's a bracket that it will fit # CE10304G but we do not carry a 10" wide roller. If...
  view full answer...
• Brackets to Install Keel Rollers Above a Boat Trailers Frame
  If I understand what you're trying to do I think we can help. We have the Adjustable Mounting Brackets for Keel Rollers # CE32004G. They'll install onto your trailer's frame and will hold a keel roller that is the width of the frame plus 2 inches. If you need a 10 roller # YR1000Y will work on the brackets using # CE10726A. If I missed the mark and misunderstood you just let me know.
  view full answer...
• Can V-Keel Rollers be used on a Wood Sea Wall to Move a Pontoon Boat
  This could work but make sure the wall can handle it. The roller, # YR1000Y, does not have an official capacity but just for the ease of moving the boat on them I would use as many rollers as could fit. The issue is that since the entire boat is not supported at the same time, it could end up damaging the boat. Another option is to construct a device like in the picture I have included using rollers, # DL21741, and some lumber. With this type of set up, it would be very easy to move the...
  view full answer...
  
• Roller Shaft Length Required For Yates 10 Keel Roller and Yates End Caps For Boat Trailer
  For the Yates Keel Roller # YR1000Y with the Yates Endcap # YR135-5Y on both sides you will need a 5/8" roller shaft. I recommend the Roller Shaft with Pal Nuts # CE10727A. This shaft has an end length of 13" and includes 2 pal nuts. The endcaps are each 1" in length and have a recessed area to accept the pal nuts. To make up the 1" difference you can either cut 1" off the length of the shaft or add Flat Washers # 1140357 on each side of he endcaps allowing you to use the longer shaft....
  view full answer...
• Picking Out Non Marking 10 Inch Keel Roller for Boat Trailer
  For replacement rollers the correct size would be the YR1000Y which is a non-marking compound and was designed for a 5/8 inch shaft diameter. This is only shaft diameter size we offer at this time so for a replacement shaft with pal nuts you'd need the part # CE10727A.
  view full answer...
• What is Included in the Yates Rubber Boat Trailer Part # YR1000Y
  The Yates keel roller # YR1000Y you referenced will not include a shaft and pal nuts. You will need to get part # CE10726A which will include 1 shaft and 2 pal nuts.
  view full answer...

Do you have a question about this Boat Trailer Part?