# 1
Ultimate Trailer Jack - A-Frame - Topwind - 27-1/2" Lift - 2,000 lbs
This is an excellent replacement for the jack on my Legend 16' V-nose with aluminum frame, it was easy to install, mounting flange matched perfectly. This style trailer sits very low and has always been a headache going in and out of gas stations, ect. The original style Jack foot hits "sometimes very hard," even when the jack is cranked all the way up. Now I rotate the top pin, remove the bottom foot pin and remove the complete Jack and store it in the back of the truck, takes 30 seconds.
Mine arrived with a drill bit end broken into the release handle. In fact, the drill bit was what was holding it together. I don't know what a production unit has in that through hole (a roll pin?). Regardless, it isn't something you want to find in a new jack. After I punched it out, I added a snap ring pin to hold it in place. One other comment would be that the foot needs to be unbolted in order to remove the jack. Ideally a locking pin would have been better than the bolt for a "no-tools-needed" removal.
# 2
Round A-Frame Trailer Jack - Sidewind - 15-5/8" Travel - 5,000 lbs
I purchased this JA-5000S-B Sidewind jack for my 20' Car Hauler because I added a Harbor Freight toolbox that was taller than my top wind jack. This one is somewhat taller than the one replaced and moves the wind handle toward the truck. In my case the tailgate still drops and clears the handle by 10" or so. The jack is a little slower than the last one but has a higher weight rating (5000 lbs) etrailer always helps with the selection and has been a great resource.
Existing job site trailer jack broke Thursday. Menards, Home Depot, Northern tool, Mill didn't have the needed style in stock. Ordered it up and got here on Saturday. Perfect fit and higher weight rating than previous jack. Cranks smooth.
# 3
Square Direct Weld Jack w/ Footplate - Drop Leg - Sidewind - 28-7/8" Lift - 7,000 lbs
Great product, just what I was looking for. I've purchased 8 of these Jack's in the past few months and very happy with them. 2 days at my door after placing order to witch is impressive
7000 lb trailer jack with grease fitting is smoother than I expected. Great Value. Easy on line order and great shipping. Thanks for the attention to my order
# 4
Bulldog Round, A-Frame Jack - Sidewind - 15" Lift - 5,000 lbs
ordering was an easy and simple process. Tracking process and delivery time was top notch. Will order from etrailer.com again!
After the gears on my original/stock A-frame sidewind jack had stripped and failed (BAL 2000 mounted on my 2017 Forest River Rockwood mini-lite model 2306 with a dry weight of 4005 lbs), I replaced it with another BAL 2000 sidewind model which lasted less than 6 months before the gears also had stripped and failed. After reviewing numerous A-frame jack sidewind models, I decided to purchase the Bulldog A-frame sidewind model with a rating of 5000 lbs and a 15" lift. I also purchased the corresponding foot pad to help with the distribution of weight. The installation was straightforward and simple and so far, I have not experienced any functional issues with the jack. For anyone searching for and in need of a high quality and capable A-frame sidewind trailer jack, I would highly recommend this particular model.
# 5
Pro Series Round, Snap-Ring Swivel Jack - Bolt On - Topwind - 10" Lift - 2,000 lbs
I needed a swing jack for my 25' boat trailer, to move it around without hitching to my truck. As you can see, by the pictures, I bolted on a 10" lawn / garden swivel caster to the foot of your jack. This way I can drop the jack down and raise the original jack up (which has a too small wheel that sinks into my soft yard). In this way I use my lawn tractor to move the boat around my yard. Hitched to my truck and the rig is to long to maneuver.
This jack is perfect. It fits my trailer well, seems well built, and was easy to install. Some of the other jacks I looked at locally seemed like they were mounted loosely and would rattle around. This one is tight against the trailer and doesn't rattle while driving.
# 6
etrailer Boat Trailer Jack w/ Footplate - Sidewind - Fixed Mount - 29-1/8" Lift - Zinc - 2.5K
Excellent delivery time! Very quick and easy installation. The jack feels well made the cranking is smooth. Highly recommend this jack.
Exactly what I needed for my boat trailer. When retracted it clears the road. The flip up hitch that was on it could not handle the salt water dips and seized up after a year. This is a lifetime jack.
# 7
Square A-Frame Jack w/ Footplate - Drop Leg - Sidewind - 28-3/4" Lift - 3,000 lbs
Jack works great. Damaged the original when I forgot to lift the foot and hit my concrete parking apron. After I straighten out the mount this jack fit the hole perfectly and works great.
Instillation was very easy and it works amazingly. My trailer had a electric jack before and I was always having to maintain a battery, now I don't he to mess with that and it lifts super easy. I highly recommend this jack for enclosed trailers or heavy tongue weighted trailers.
# 8
Pro Series Snap-Ring Swivel Marine Jack - Bolt On - Sidewind - 10" Lift - 1,000 lbs
Perfect replacement for my jet ski trailer. Easy installation and fast shipping from etrailer. Thanks!
Easy install to provide greatly improved unhitched trailer handling. This item was the final component to complete a refurbished trailer for my catamaran. My project started with a 1987 Calkins single-axle used trailer, adding the following E Trailer parts: 1. Miro-Flex Trailer Stop/Turn/Tail Light unit 2. CE Smith V-Wing Bolster Brackets 3. Rectangular Trailer Reflectors, Adhesive Mount - Amber 4. Erickson Hide-A-Hook Truck or Trailer Anchors 5. Pro Series Snap-Ring Swivel Marine Jack and completed with a hand-built frame assembly and covered bunk boards.
# 9
Pro Series Round, Pipe-Mount Swivel Jack w/ Footplate - Sidewind - 15" Lift - 5,000 lbs
Package arrived a day early. Jacks were just as I expected and best price I found. Can’t wait to get them welded on. Will be buying more jacks in the future. Best selection I’ve found as well.
Purchased to stabilize my recently obtained trailer for hauling my tractor. The jacks add a great deal of security and safety to the operation by allowing me to block the downward movement of the rear of the trailer while driving the tractor onto it, then being able to remove them once loaded for transport.
# 10
Bulldog A-Frame Round Jack - Sidewind - 15" Lift - Zinc - 5,000 lbs
Pretty sure this is the model that came with my new BoatMaster Trailer many years ago. Anyway, much better than the last jack stand which started rusting less than a year. The new Bulldog, at least on my A-frame trailer, could only be installed with the handle facing forward, which is fine, especially since it is much easier at lifting its weight compared to a top-wind, rusty 1,000 jack that it replaces. I'll let you know if it lasts and doesn't start rusting prematurely or develops winding/gear problems.
i replaced my old jack with this one and it is harder to crank then my older one. probley putting the old one back on.
# 11
Round, Pipe Mount Swivel Jack w/ Footplate - Weld On - Zinc - Topwind - 10-3/4" Travel - 2K
Worked perfectly for supporting the rear of the trailer for loading my tractor Mounted one on each side on rear of trailer
Good inexpensive jack. I ordered two. My use for them is somewhat "off label". My 19" 9000# capacity flatbed trailer has a label on the dovetail indicating that the rear of the trailer should be supported for any loads over #3000. Personally I think supporting the rear for a trailer is always a good idea when loading and unloading. It puts less strain on the rear of the trailer and it prevents the trailer from lifting the rear of the tow vehicle during loading which can be extremely dangerous. I had a friend weld the tube mounts on each side of the rear of the trailer. See pictures below. Now I don't need cribbing or chunks of wood to shove under the rear of the trailer. These will also adapt well to uneven ground. They can be stowed horizontally, like in the picture or removed when not needed.
# 12
Square Pipe Mount Swivel Jack w Footplate - Drop Leg - Weld On - Topwind - 28-7/8" Lift - 7K
Was having issues with the trailer lifting the backend of my truck when I loaded tractors. When I would drive the tractor on the back of the trailer would go down from the weight on the rear which caused the front of the trailer to lift the backend of my truck. So, I bought a couple of the Square, Pipe Mount, Swivel Jacks with Footplates and a Drop Leg. They are Topwind, 7K, Jacks. I had them welded on. This should stop the issue I'm having. I know the 7K was a little over kill but the price was great.
So far been holding up very well. Used as a tongue jack on some hopper bottom pup trailers and these jacks give us the reach to be able to unhook them from the pintle without need to hunt around for wood blocks to place under the jack.
# 13
Pro Series Round, A-Frame Jack w/ External Gearbox - Sidewind - 14" Lift - 2,000 lbs
Mounted on the bottom of the new trailer jack i bought from etrailer. Everything works as advertised. Fair price and great customer service
seems to be good frame jack
# 14
Bulldog Round, A-Frame Jack - Topwind - 15" Lift - Zinc - 2,000 lbs
The jack was in stock, the shipping process started immediately, and it was delivered when promised! Thank you.
Replaced original on the trailer. Works perfectly and easy install.
# 15
Pro Series Square Jack - Front Pin Drop Leg - Spring Return - 10K Lift - 26" Travel
We've installed these on several trailers for out autorestoration and custom welding shop in detroitlakes mn, we also build bumper jacks and other lifting equiptment out of these. Etrailer sells them at the best price ,and packaging/shipping was impressive too. Even beaten half to death, scratched, dented, left in the weather, mud and rust, these things still work effortlessly, theyre the only way to go and easy to hook to hyraulic, chain, motor or cable drives for hands free operations !
this trailer jack is easy to lift your trailer. It also has grease fittings to keep it turning easy. Good product
# 16
Pro Series Round, Pipe-Mount Swivel Jack w/ Footplate - Sidewind - 10" Lift - 2,000 lbs
The jack on my cattle trailer wore out. I ordered a replacement from etrailer and within a couple of days the new jack was delivered. My son, a welder, cut the old jack off and installed the new jack. The new jack is so superior to the old one. The ability to turn the jack parallel and out of the way is great. I am sending before and after photos. Thanks for the great service and product!
The action is smooth and the construction sturdy. A+
# 17
Buyers Products A-Frame Jack w/ Support Foot - 15" Travel - 5,000 lbs
Have used this on a flatbed for over a year. Has worked flawlessly and recommend this jack. If the weight rating matches your needs, this is an excellent product for the price point.
Easy installation, seems sturdy, and no problem in raising or lowering the. Wish it was made in the USA. Replaced the coupler at the same time, as the picture shows
# 18
Round, Pipe Mount Swivel Jack w/ Footplate - Weld On - Sidewind - 10" Travel - 3,000 lbs
Good price, exactly what I needed. Order fulfillment times can't be beat.
Great product at a great price. Used the chat and and got great help quickly.
# 19
etrailer Boat Trailer Jack w/ Wheel - Sidewind - Swivel - 10" Lift - Zinc - 1,000 lbs
Great product at a fair price. etrailer customer service is second to none.
Heavy Duty works as expected. Arrived in short order. Installed in minutes. Thank you etrailer!
# 20
Bulldog Square Jack w/ Footplate - Drop Leg - Sidewind - 28-1/2" Lift - 7,200 lbs
Im starting to wonder about shipping
ordered the wrong jack and was sent a return freight label, and i ordered this one right away good service. waiting to receive my credit minus shipping
What our customers are saying:
"We received our trailer on Thursday. Thank you for your quick action."