Lubrication and Greasing Recommendations for a Trailer Valet JXC Trailer Jack

Question

Question:

Hi I purchased one of these last year and was curious on the maintenance. I see there is what looks like a grease zerk and was wondering what I should use for use to get it in there to keep things lubricated. Thank you Have a good day

asked by: Keegan

0

Expert Reply:

There isn't any specific maintenance requirements for your Trailer Valet JXC Trailer Jack w/ Footplate and Drill Powered Option # TV94FR, however I do recommend applying some grease # L11390 using the grease zerk you're looking at to lubricate the gears on the inside of your jacks.

You can also lubricate the jack tube with some Roadmaster LubeMaster Dry Silicone Spray # RM-747.

expert reply by: Bryce D

0

Answer 1

The grease zerk on the Trailer Valet JXS Trailer Jack #TV64FR will provide Grease #L11390 to the gears inside the head of the jack. This is the only place that I recommend using grease on the jack. I recommend using a dry spray lube like the…

view full answer...

Answer 2

Hello, and thanks for getting in touch. The etrailer Electric Trailer Jacks #e55ZV and #e23ZV will hold up just fine in cold weather. The housing is designed to be water/weather resistant. It even has a manual backup option if you were to lose power…

view full answer...

Answer 3

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

Hello Michael, Happy to get the right jack for your SunTracker. I looked up the specs for the weights, the boat itself is about 3,000 pounds, the motor is around 500 pounds, then fuel, gear and batteries around 400 pounds, and the trailer itself is…

view full answer...

Answer 7

Hey Paul, great question! The etrailer Ladder Rack #e78FV and Erickson Ladder Rack #EM07707 are very similar, but the value trade-off between the two is huge. One thing you'll notice is we have a lifetime warranty on our rack versus the typical…

view full answer...

Answer 8

Hello Jeremy, Yes, our etrailer jack #e55ZV will automatically stop and not over raise. If you check out the video that I attached you will see that Steven still has his finger pushing down the button after the jack stops. What kind of application…

view full answer...

Answer 9

The biggest difference is that from the RVK3000 to the Companion #BWRVK3500 the capacity was upgraded from 18,000 lbs to 20,000 lbs. The height adjustability also changed from 14-3/4 inch-16-3/4 inch to 16-1/4 inch-18-1/4 inch. The post that attaches…

view full answer...

Answer 10

The mounting hole dimensions of A-frame jacks are a standard 3 inches apart on center, so you will need to weld your new jack on. I highly recommend the etrailer Round, A-Frame Jack #TJA-5000S-B, which has a 5,000 lb capacity and will give you…

view full answer...

Answer 11

Joe, the WS Aero Hitch 6" Drop Hitch w/ 2" Shank #WS67MR is available with a 4" #WS54UR, 10" #WS42RR, and 8" #WS45RR drop length.

view full answer...

Lubrication and Greasing Recommendations for a Trailer Valet JXC Trailer Jack

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching