Replacement Cradle for a Thule Passage Trunk Mount Bike Rack

Question

Question:

For the Thule Passage TH910XT, does the T3 cradle 853-5829 serve as a replacement cradle? According to specs/size measurements it should, I just want to verify with the experts.

asked by: Gregg

0

Expert Reply:

The correct replacement cradle for the Thule Passage bike rack # TH910XT is actually the Stay-Put cradle # 853-7887. If you also need a strap it is # 852-3006-001 and the anti-sway cage that fits is # 853-7758.

expert reply by: Michael H

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

Hello Lou, thanks for reaching out. The hitch pin you are looking for is the etrailer D-Shape Anti-Rattle Locking Hitch Pin for Benton Hitch Accessories #e43JR. This will work with the Benton #B54VR bike rack you mentioned, as well as the #B54FR,…

view full answer...

Answer 5

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Answer 6

For your Thule Roadway 4 Bike Carrier for 1-1/4" and 2" Hitches TH914XT, which is no longer available, I recommend replacing your current Stay-Put Cradles #853-7887 with the: -Replacement T2 Cradle Body for Thule Bike Carriers #853-5829.…

view full answer...

Answer 7

Though this does look remarkable similar to the Thule Hitching Post Pro #TH934XTR, to my knowledge this rack was never offered with just a 2" shank as it used a 1-1/4" shank with a 2" adapter, so I can't say exactly which model you…

view full answer...

Answer 8

When replacing the Replacement Hold Fast Cradle for Thule Archway and Apex Bike Racks #7521513002, the previous cradles may have screws in which case you can just reuse them and be done with it. If it happens to have rivets, which you can look on…

view full answer...

Answer 9

The only Thule cradle that would fit would be the T3 cradle #853-5829 which also fits on 1 inch diameter arms and has a very wide and flat top portion. You would also need different anti-sway cradles, #753-3530. You may need to use an adapter bar…

view full answer...

Answer 10

Judging by your photos, you definitely have the Thule Expressway 995. I have exactly what you need! I went ahead and confirmed with Thule that the direct replacements are the Replacement T2 Cradle #853-5829 and the Replacement Rubber Strap #753-3535.…

view full answer...

Answer 11

Originally, your Thule 947 Hitching Post bike rack used cradles that had straps built into them. Thule doesn't make those cradles any more, but the Thule #853-7887 would be the closest replacement, assuming that the bar on your bike rack is 1…

view full answer...

Answer 12

The Thule Helium Platform Bike Rack part #TH53GC has a distance of about 11 inches from the center of the hitch pin hole to the nearest wheel tray. So to determine if this could fit past the spare of your Jeep Wrangler you'd need to measure from…

view full answer...

Replacement Cradle for a Thule Passage Trunk Mount Bike Rack

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching