Recommended Bunk Board Replacement Options for Boat Trailer

Question

Question:

I have Qty 2 of 2inch x 4inch x 24inch L side bunks that I want to simply replace bc they look old. Can you give me the options for that? Also, why does the bottom have 2 sets of bunks on each side of the boat? My boat is 17.1foot long then you add what 2inch past the stern, so if you add all that up I would need 8.6foot long bunks? Would i be ok to go with 7foot since that is longest you offer? I believe on the bottom one bun is longer than the other on each side. It is a 1995 Astro 17cc center console boat with EZ loader trailer.

asked by: Brett M

0

Expert Reply:

For your boat trailer, the length of bunks is dependent on the boat and the trailer, so I would be hesitant to change anything from the factory. It soulds like you have a couple of 2 foot bunk boards that need to be replaced and you can use the CE Smith Carpeted Johnboat Bunk Board for Boat Trailers - 2' Long - Qty 1 # CE27850 for the replacement.

You can use shorter bunk boards in combination to reach your current lengths. Doing so will sometimes even increase the strength because the stress is not as drawn out on the grain of the wood and at times additional brackets are needed which increases support.

You can use the following:
CE Smith Carpeted Bunk Boards for Boat Trailers - 3' Long - 1 Pair # CE27800
CE Smith Carpeted Bunk Boards for Boat Trailers - 4' Long - 1 Pair # CE27810
CE Smith Carpeted Bunk Boards for Boat Trailers - 5' Long - 1 Pair # CE27820
CE Smith Carpeted Bunk Boards for Boat Trailers - 6' Long - 1 Pair # CE27840
CE Smith Carpeted Bunk Boards for Boat Trailers - 7' Long - 1 Pair # CE27845

Your final option is to use locally obtained treated boards and then use the marine carpet in your desired color and length. You will want to get stainless steel stables from your local hardware store for attaching that marine carpet.

expert reply by: Jason S

0

Answer 1

The general rule of thumb is that you want your bunks to extend completely to the stern (rear) of the boat, or even and inch or two beyond. That way the transom has plenty of support as you drive down the road. The bunks can extend as far forward as…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 8

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 9

The three most common lug stud sizes for a trailer are 1/2"-20, 9/16"-18, and 5/8"-18. In order to make sure you get the correct lug nuts you need to measure the lug studs on the trailer now as we have no way to look this up for…

view full answer...

Answer 10

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 11

I currently have three diffrent self-adjusting assemblies for your boat trailer with 10" x 2-1/4" electric drum brakes which are attached for you below. eTrailer Electric Trailer Brake Kit part #AKEBRK-35-SA (3,500 Axles) Dexter…

view full answer...

Answer 12

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Recommended Bunk Board Replacement Options for Boat Trailer

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching