See what our Experts say about this CE Smith Boat Trailer Parts

• Recommended Bunk Board Replacement Options for Boat Trailer
  For your boat trailer, the length of bunks is dependent on the boat and the trailer, so I would be hesitant to change anything from the factory. It soulds like you have a couple of 2 foot bunk boards that need to be replaced and you can use the CE Smith Carpeted Johnboat Bunk Board for Boat Trailers - 2' Long - Qty 1 # CE27850 for the replacement. You can use shorter bunk boards in combination to reach your current lengths. Doing so will sometimes even increase the strength because...
  view full answer...
• Replacement Bunk Boards and Brackets for 17 Alumacraft Boat Trailer
  You should be able to just measure the length of your roller bunks and then replace them with carpeted bunks that match. I am attaching a link to our selection of bunk boards which range from 2' # CE27850 to 7' # CE27845. If you're needing to replace the brackets and hardware too then I'm also linking our selections of those for you to filter through. Basically if your boat currently fits really well on your current setup then you want to match everything up as best as possible so you...
  view full answer...
• Recommended Carpeted Bunk Boards And Carpet For Tandem Boat Trailer
  If you are looking for carpeted bunks for your tandem boat trailer we offer 5 different lengths for you. The boards come in 2 ft, part # CE27850, 3 ft, part # CE27800, 4 ft, part # CE27810, 5 ft, part # CE27820, and 6 ft, part # CE27840. Each of these bunk boards is a 2 x 4 covered with marine-grade carpet that helps protect the hull of your boat as it is loaded and unloaded. If you have longer bunks and you want to cover the bunks you have we carry marine-grade carpet that would work...
  view full answer...
• Adding Bunks and Brackets to a Pontoon Boat Trailer
  We have some bunk boards and brackets that you could use for your pontoon boat trailer. I have included a link to the bunk boards for you. Most of the them do not come with brackets, with the exception of # CE27850, but we have numerous bracket options as well. We also have bunk style guide-ons for pontoon boat trailers, # CE27671, if you are looking for something like that. For bunk brackets we have CE Smith Bolster and Swivel Bracket Assemblies - Galvanized Steel - 9" - Qty 4 Item #...
  view full answer...
• Availability of Crossbar System from the Malone MicroSport Trailer # MPG460G
  The Malone MicroSport Trailer # MPG460G uses crossbars like what you would find on the roof of a vehicle instead of bunk boards. This is sold on our site as the Malone Crossbar Conversion Kit # MPG475 and it comes with the mounting hardware. If you are wanting carpeted bunk boards instead we have them in the following lengths: 2' - # CE27850 3' - # CE27800 4' - # CE27810 5' - # CE27820 6' - # CE27840 These come in pairs.
  view full answer...
• Trailer for Sea Eagle Stealth Stalker 10
  For your Sea Eagle Stealth Stalker 10 I recommend the CE Smith Multi Sport Plus Boat and Kayak Trailer w/ Bunks # CE48870. In addition to the bunk boards it comes with I would also add the CE Smith Carpeted Johnboat Bunk Board for Boat Trailers # CE27850 up on the tongue for extra support. You can secure it by the front handle using the winch and then add some ratchet straps like # e82JR for the sides and # IMF08893 to secure it by the rear handles. You may not need ratchet straps that...
  view full answer...
• Replacement Bunk Boards for a Boat Trailer
  We do have a selection of bunk boards available which you can use for a variety of lengths. Below are the different lengths we carry: 2' - # CE27850 3' - # CE27800 4' - # CE27810 5' - # CE27820 6' - # CE27840 7' - # CE27845 Since bunk board brackets can sit at different locations along the boat frame you'll just need to compare the different lengths to what you currently have and you'll be good to go!
  view full answer...
• Does Ribs of Bottom of Johnboat Affect Use of CE Smith Carpeted Johnboat Bunk # CE27850
  The ribs of your John boat are actually very strong and the design of them gives the metal quite a bit more strength than if the bottom of the boat was totally smooth. Due to that the CE Smith Carpeted Johnboat bunk part # CE27850 that you referenced would work fine for you.
  view full answer...
• Type And Size Bolts To Attach Swivel Bracket To Carpeted Bunk Board.
  For bunk brackets we have CE Smith Bolster and Swivel Bracket Assemblies # CE10000G-4 as well as others at different lengths. To attach the brackets to the trailer frame you can use U-bolts such as # CE15283GA-2 which are 3-13/16 inches long, 3-1/16 inches wide, and have a 1/2 inch diameter. Or you could use # CE15283GA-4 which is the same thing only it comes with 4 U-bolts instead of 2. These mounting slots, are a length of 2-3/4 of an inch. There is a width of a 1/2 inch spacing in...
  view full answer...
  
• Availability of Different Length Bunk Boards for Boat Trailer for 1983 MonArk
  Since you are referencing the CE Smith Carpeted Johnboat Bunk Board for Boat Trailers # CE27850 which runs across the trailer, I am assuming by width you mean the length of the board. The bunk board that comes with the # CE27850 is 2' long, and we do have other sizes. These bunk boards come in the following lengths: 3' - # CE27800 4' - # CE27810 5' - # CE27820 6' - # CE27840 7' - # CE27845 All of the bunk boards are 1-3/4" wide x 3-3/4" tall and come in pairs with the exception of the...
  view full answer...

Do you have a question about this Boat Trailer Part?