Availability of a Pipe Mount Trailer Jack with Caster Wheel
Question:
I need a pipe mount jack with the option of a caster wheel.
asked by: Lou
Expert Reply:
I have a couple of jacks that I can recommend for you, but at this time we do not have a pipe mount jack available with the option of a caster wheel.
The first and best fit would be the Bulldog Rack-and-Gear Jack with Steel Wheel - Weld On/ Bolt On - 16 inch Lift - 750 lbs, item # BD162300, which has a angle mounting plate that is 3-1/2 inches tall by 1-3/4 inches wide. If the fact that this jack does not swivel up out of the way is acceptable, it would be your best bet.
The second is the Fulton F2 Swing-Up Trailer Jack, Dual 7 inch Wheels, Sidewind, Weld-On - 1,600 lbs, item # F1413060334, the mounting bracket on this jack is larger, at 5-3/4 inches wide by 4-3/4 iches tall and you would have to do some creative welding to secure it to the trailer frame, which would not look so good in the end, most likely. This is the closest size swivel jack that I have that might work for your trailer.
Products Referenced in This Question
Fulton F2 Swing-Up Trailer Jack, Dual 7" Wheels, Sidewind, Weld-On - 1,600 lbs
- Trailer Jack
- Boat Trailer
- Enclosed Trailer
- Utility Trailer
- Side Mount Jack
- Swivel Jack
- Alloy Aluminum
- 1001 - 2000 lbs
- Manual Jack
- 10 Inch Lift
- Weld-On
- With Wheel
- Fulton
more information >
Product Page this Question was Asked From
Pro Series Round, Pipe-Mount Swivel Jack w/ Footplate - Sidewind - 10" Lift - 5,000 lbs
- Trailer Jack
- Car Hauler
- Enclosed Trailer
- Utility Trailer
- Side Mount Jack
- Swivel Jack
- Steel
- 4001 - 5000 lbs
- Manual Jack
- 10 Inch Lift
- Pipe Mount
- Weld-On
- With Rectangle Foot
- Pro Series
more information >
Continue Researching
- Shop: Bulldog Square Swivel Jack w/ Round Pipe Mount - Drop Leg - Sidewind - 28-1/2" Lift - 5,000 lbs
- Q&A: Will Pro Series Jack # PS1401460303 Fit etrailer Pipe Mount # e52JR
- Search Results: swivel jack
- Shop: Square Pipe Mount Swivel Jack w Footplate - Drop Leg - Weld On - Sidewind - 28-1/2" Lift - 7K
- Q&A: Recommended Square Swivel Jack with Foot for Trailer Tongue with 5,000 lb Capacity
- Q&A: What are the Measurements on a Bulldog Square Swivel Jack # BD190758
- Video: Bulldog Square Swivel Jack w/ Round Pipe Mount Review
- Video: Review of the Bulldog Square Swivel Jack w/ Round Pipe Mount
- Video: Feature Breakdown: Replacement Female Pipe for etrailer and Ram Pipe Mount Swivel Jacks
- Shop: Pro Series Round, Pipe-Mount Swivel Jack w/ Footplate - Sidewind - 10" Lift - 5,000 lbs
- Search Results: e track rails
- Search Results: etrack
- Search Results: etrack
- Search Results: sidewind
- Shop: Brophy Horizontal E Track - Zinc Plated Steel - 5' Long - Qty 1
- Search Results: standard grease cap trailer bearings races seals caps
- Shop: Square Pipe Mount Swivel Jack w Footplate - Weld On - Sidewind - 15-1/4" Travel - 3,000 lbs
- Shop: etrailer Horizontal E Track - Galvanized Steel - 2,000 lbs - 94" Long
- Shop: Bulldog Round, Pipe-Mount Swivel Jack - Sidewind - 15" Lift - 5,000 lbs
- Video: Review of the Bulldog Round Jack without mount
- Video: Feature Breakdown: Pipe Mount Swivel Style Trailer Jack with Foot
- Video: What to Know About the Bulldog Square Jack with Footplate
- Video: Pro Series Round, Pipe-Mount Swivel Jack w/ Footplate Review
- Search Results: trailer jack
- Shop: Trailer Hitch
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Article: Trailer Wiring Diagrams
- Q&A: Is E-track Stronger Than X-track, Is There An Advantage Of One Over The Other
- Shop: RV Bearing
- Article: How to Measure Your Trailer Wheel Bolt Pattern
on Trailer Jack
Steve G.
7/13/2020
Your Bulldog Round Pipe-Mount Swivel Jack with pin attachable wheel should do what I need. Two are required. My Norwood sawmill with integral trailer has six swivel jacks for adjustable level support at log sawing site. My tractor tows this trailer in and out of a fairly large storage garage with smooth concrete floor. When I back the trailer (portable bandsaw sawmill) into the garage, I want to remove the front two plate bottom jacks from their 2 1/2" female mounts and substitute your castor fitted swivel jacks. After I disconnect the trailer from the tractor, I can push the trailer into the best storage location by hand. Your two jacks at the tongue end of trailer will work with the trailer wheels to make a balanced and mobile rig for indoor parking. Can we do this? Ideally, there are 11 to 12 inches below the female side supports for the jacks to the floor when the trailer is level.