Recommended Square Swivel Jack with Foot for Trailer Tongue with 5,000 lb Capacity

Question

Question:

I am seeking a tongue trailer jack of the following configuration: Side Frame Mount Jack Swivel Jack - Pull Pin Weld-On 5000 lbs Sidewind Jack 15 Inch Lift Square Shaft With Square Leg With Foot

asked by: Steve T

0

Expert Reply:

The Bulldog Square Swivel Jack w/ Round Pipe Mount - Fixed Leg - Sidewind - 15" Lift - 5,000 lbs # BD190756 is my recommendation for you. It meets all of your criteria and is a great quality jack.

expert reply by: Jason S

0

Answer 1

Hey David, yes the Pro Series jack part #PS1401460303 will work with the pipe mount part #e52JR as they are both 2 inch.

view full answer...

Answer 2

I pulled the Bulldog square swivel jack #BD190758 from our warehouse to provide the measurements you requested. The jack is 26-inches in overall length, not including the handle. The handle radius is 8-1/2 inches for your reference. If the foot base…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 12

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Recommended Square Swivel Jack with Foot for Trailer Tongue with 5,000 lb Capacity

Featured Help Information

Miscellaneous Media

Continue Researching