What our customers are saying:
very easy to shop
Mike
Richmond, CA
Videos
for Lift Supports
Help Articles
Expert Answers
Hey thanks for reaching out, Robert. Your Dexter P-15 model SLR 3,500 lb axle does use the standard bearing combination for a 3,500 lb axle. I was able to confirm this with Dexter. So, you have #L68149 for the inner bearing and #L44649 for the…
The Air Lift LoadLifter 5000 #AL88200 will work with the Air Lift Air Helper Spring Cradle #AL59DQ on your 2013 Ford F-150. The cradle actually replaces the lower roll plate so the air bag will sit directly in the cradle. I'm not…
Hi Robert; the Hub Bearing Kit for Lippert, Dexter, and AL-KO Axles - 3,500 lb with #84 Spindle #BK2-100 is the correct bearing kit for your axle.
Hey Jason, so we don't have the Hopkins tailgate assist part #74211 listed as a fit for your 2011 Ford F-350 but we do have the DeeZee part #DZ43203 as a fit.
I have included a video that briefly goes over installing the Hopkins EasyLift Truck Bed Tailgate Lift Assist #74211 but we do not have a video that goes over the entire installation process. As you can see in the video you will need to drill a…
You are correct that is a 3,500 lb axle. If you want a bearing kit the #BK2-100 you looked at is the right one. This comes with a #L44649 outer and #L68149 inner bearing along with a #58846 (10-19) grease seal. If you want a replacement idler hub…
Hey Lucas, The Curt MV #C17050 is for total tongue weights between 500 lbs and 600 lbs only (600 lbs isn't actually the minimum), and for a 5,000 lb GVWR camper, the tongue weight is definitely going to exceed what this hitch is…
Thank you for all the info John, Based on the numbers you provided your pin box has a Rhino bolt pattern with a 21,000 capacity. To find the correct Gen-Y pin box we'll need to check your trailer's pin weight. If the…
To flat tow a 2011 to 2013 Jeep Grand Cherokee there are 5 major components needed: base plates, tow bar, safety cables, lighting, and supplemental braking. The base plates are what attach to the front of the Jeep and provide a safe and proper…
Yes, the #TLD2142 is exactly what you need for your 2019 Ram 3500 with running boards extending under the truck bed. For the rear, you need the #TLD3112 if you have the factory hitch or #TLR3510 if you have the TorkLift SuperHitch Magnum 30K.
Yes, the Dexter E-Z Flex Suspension Kit #K71-657-00 is the correct kit to upgrade your triple axle trailer which currently utilizes the 13-126 equalizer. Both these are designed for axle spacings 35" apart.
The Gen-Y Hitch Shock Absorbing 5th Wheel Pin Box #GY68GR is roughly 2" shorter than the Lippert 1621 pin box. I've attached a dimensional drawing of #GY68GR for you to check out as well.
Search For Custom Fit Ford Mustang AccessoriesSelect A Category Below
Towing
Ford Mustang Trailer Hitch
Ford Mustang Trailer Wiring
Ford Mustang Brake Controller
Ford Mustang Base Plate for Tow Bar
Ford Mustang Vehicle Tow Bar Brake System
Ford Mustang Vehicle Tow Bar Wiring
Ford Mustang BOLT brand vehicle and hitch locks
Cargo Control
Ford Mustang Roof Rack
Ford Mustang Trunk Bike Rack
Performance Accessories
Ford Mustang Air Filter
Ford Mustang Exhaust
Ford Mustang Suspension Enhancement
Ford Mustang Transmission Cooler
Ford Mustang Performance Chip Tuners
Ford Mustang Vehicle Lights
Ford Mustang Tire Chains
Ford Mustang Fluid Filters
Ford Mustang Catalytic Converters
Ford Mustang Vehicle Engine Heaters
Ford Mustang Radiator Fan
Ford Mustang Cabin Air Filter
Ford Mustang Lift Assist
Vehicle Trim
Ford Mustang Floor Mats
Ford Mustang Trim Kits
Ford Mustang Vehicle Covers
Ford Mustang Grille
Ford Mustang Bug Shield
Ford Mustang Vehicle Seat Covers
Ford Mustang Replacement Mirrors
Ford Mustang Windshield Wiper Blades
Ford Mustang Windshield Covers