Tailgate Specs:
Features:
This strong-as-steel plastic tailgate features a cutout that makes it perfect for towing a 5th-wheel or gooseneck trailer. The locking tailgate has built-in louvers that reduce drag, and it mounts securely with rotary latches and coated cables.
More Information >Tailgate Specs:
Features:
This strong-as-steel plastic tailgate features a cutout that makes it perfect for towing a 5th-wheel or gooseneck trailer. The locking tailgate has built-in louvers that reduce drag, and it mounts securely with rotary latches and coated cables.
More Information >Tailgate Specs:
Features:
This strong-as-steel plastic tailgate features a cutout that makes it perfect for towing a 5th-wheel or gooseneck trailer. The locking tailgate has built-in louvers that reduce drag, and it mounts securely with rotary latches and coated cables.
More Information >Tailgate Specs:
Features:
This strong-as-steel plastic tailgate features a cutout that makes it perfect for towing a 5th-wheel or gooseneck trailer. The locking tailgate has built-in louvers that reduce drag, and it mounts securely with rotary latches and coated cables.
More Information >Videos
for Tailgate
Help Articles
for Tailgate
Expert Answers
for Tailgate
I do have an option for you, but we do not carry the Dexter 072-027-00 you mentioned. However we do have the etrailer Double-Eye Spring for 7,000-lb Trailer Axles - 24-7/8" Long #e64SR which will be 3/8"…
view full answer...The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.
view full answer...The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.
view full answer...Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached…
view full answer...Yes, you can use the NOCO GEN On-Board Battery Charger #NOC34FR on your pickup's parallel batteries without disconnecting them. If your batteries were in a series, they would have to be disconnected. Since your batteries are…
view full answer...In order to charge your batteries wired in parallel with the NoCo Genius #329-GENIUS5 you'll want to connect the positive charge line to the positive terminal of the first battery and the negative line to the negative terminal…
view full answer...The #99 trailer spindle is typically found on 9,000 lb and 10,000 lb axles. This is not a spindle that we carry at this time, but I did find some of the measurements. I have attached a diagram showing the dimensions of a #99 spindle for you to…
view full answer...According to my contact at Fantastic Vent the correct replacement lift motor to use in your vent is part #FVK6010-81, not item FVK-6050-80. The replacement motor does operate at a higher 17-RPM speed. Since your fan is of a lower rpm and…
view full answer...The DeeMaxx item #DE86VR won't because of the spacing on the mounting bracket but I have a caliper that will. To replace your Tie Down Engineering 46304 caliper you will need the Kodiak Disc Brake Caliper item #KDBC225DAC.
view full answer...For a replacement you need the Titan Zinc-Plated Brake Actuator #T2477600. This is the Titan Model 10 which is the same as the Dexter DX12.5 you currently have on your boat trailer.
view full answer...For your 2010 Forest River R-Pod 172 that has 3,500 lb Lippert torsion axles the correct lift kit is the #LC382741 that you referenced which will give you a 3-1/2 inch lift.
view full answer...For all intents and purposes, yes, the Fulton drop leg stabilizer jack SJL80300 is the same as the square leg jack you asked about: - Square Drop Leg Stabilizer Jack - 18" Travel - 2,000 lbs #SJ-R208 Different manufacturers but…
view full answer...