What are the Dimensions of a #99 Spindle

Question

Question:

what are the actual dimensions of a #99 spindle?

asked by: Joshua K

0

Expert Reply:

The #99 trailer spindle is typically found on 9,000 lb and 10,000 lb axles. This is not a spindle that we carry at this time, but I did find some of the measurements. I have attached a diagram showing the dimensions of a #99 spindle for you to check out.

If you are looking for bearings and a grease seal, you can use part # 28580 for the inner bearing, # 25580 for the outer bearing, part # T51153 for the grease seal, and part # 6-96 for the spindle nut.

expert reply by: John H

0

click to enlarge

George H.

9/20/2024

DO YOU HAVE A HUB FOR THE 99 SPENDEL PRIOR AXEL?

Jerred H.

9/20/2024

@GeorgeH No, I am sorry we do not.

Answer 1

I did some digging on your AL KO 7,200 lb axle and it has bearings #28580 and #25580 which means you have a 99 spindle. The only hub we offer that will fit this setup is the part #99865UC3 which is a similar Titan hub but has an 8 on 6-1/2 inch bolt…

view full answer...

Answer 2

The correct replacement braking assemblies for your trailer with an AL-KO 7,200 lb axle is the Electric Trailer Brake Kit part #AKEBRK-7-SA for self adjust or part #AKEBRK-6 for manual adjust. The self adjust brakes as the name states will…

view full answer...

Answer 3

That certainly looks like an Al Ko 7,200 lb axle hub/drum. With that in mind you should check the plate on the trailer that has the VIN as well as that will tell you the trailer's overall capacities as well.

view full answer...

Answer 4

I'm not sure why they said those were your only options, but we do have the correct replacement oil seal for your Dexter 10k hub from 2006, and is the exact replacement for a National 370150BG: - Unitized Oil Seal #10-51 The #10-51 has an inner…

view full answer...

Answer 5

From the measurements you gave me, it sounds like you have an Agricultural Spindle like #TRU54FR that uses #LM67048 Inner bearing and #LM11949 Outer bearing. For a hub assembly with a 4 on 5 bolt pattern #AH15450ECOMP will work and the bearings, seal…

view full answer...

Answer 6

I have included a picture that shows the measurements needed for a spindle, bearings, seals, faces, and hubs. The spindle measurements are labeled A through F. A is the spindle shaft diameter B is where the grease seal sits C is where the inner…

view full answer...

Answer 7

I would be happy to help! The Curved Equalizer for 1-3/4" Wide Double-Eye Springs - 6-1/8" Long - 9/16" Center Hole #TREQ356 you were looking at will be an exact replacement for your current equalizers as they have the same 6-1/8"…

view full answer...

Answer 8

For the absolutely best performance and reliability you can't beat the HydraStar electric over hydraulic actuators. We have found that they are the most reliable, react the fastest and just in general work the best. For just the actuator you…

view full answer...

Answer 9

There is not a Cad drawing of the #42 E-Z Lube Spindle w/ Flange for 5.2K to 7K Trailer Axles - 2-1/4" Diameter #TRU37FR available, but I did include a diagram showing all of the dimensions. It is recommended to have a an axle shop weld the…

view full answer...

Answer 10

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 11

The closest option we have would be the part #BB60001 which has an inner diameter of 1.375 inches and an outer diameter of 1.980 inches.

view full answer...

Answer 12

We have the exact bearing part #25580 that you are looking for. The inner diameter is 1.75 inch like you said you'd need too.

view full answer...

What are the Dimensions of a #99 Spindle

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching