Replacement For Dexter DX12.5 Brake Actuator on Boat Trailer

Question

Question:

I need to replace a dexter dx 12.5 coupler on my boat trailer . I am not sure if you have that model I see a 7.5?

asked by: Matt J

0

Expert Reply:

For a replacement you need the Titan Zinc-Plated Brake Actuator # T2477600. This is the Titan Model 10 which is the same as the Dexter DX12.5 you currently have on your boat trailer.

expert reply by: Robin H

0

Answer 1

Thank you for the picture, it is helpful. I can see that you have an actuator for disc brakes. In the picture you can see the yellow label that says "disc brake actuator for use with disc brakes only". The coupler does not differentiate…

view full answer...

Answer 2

For your Dexter DX12.5 actuator, you will need to use a reverse lockout solenoid. For that we recommend the Replacement Solenoid Valve for Dexter Brake Actuators #T4748800. I have linked our install video below if you want to take a look.

view full answer...

Answer 3

Hello Sophie, we sure do! For your Dexter DX12.5 actuator you can use the following reverse lockout solenoid: - Replacement Solenoid Valve for Dexter Brake Actuators with Reverse Lockouts #T4748800

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 12

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Replacement For Dexter DX12.5 Brake Actuator on Boat Trailer

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching