Anodized aluminum electric-hydraulic actuator lets you use your brake controller (sold separately) to activate your trailer's hydraulic disc brakes. Vented end plate releases heat. Hydraulic lines and breakaway sold separately. with any standard, 5-amp-hour-battery breakaway kit (sold separately) DOT compliant Unit installs on trailer frame and connects to trailer's wiring and hydraulic brake lines (sold separately) Mounting
... for hydraulic drum brakes and 3x3 or 3x4 straight tongue. in the USA Specs: Application: hydraulic drum brakes Ball size: 2" Mounting: 3" x 3" or 3" x 4" straight tongue Capacity: 7,500 lbs 2-Year limited warranty When you apply the brakes
... for hydraulic disc brakes and 3x3 or 3x4 straight tongue. Mounting: 3" x 3" or 3" x 4" straight tongue Capacity: 7,500 lbs 2-Year limited warranty When you apply the brakes in your tow vehicle, deceleration occurs and momentum pushes your
... for hydraulic disc brakes and 3x4 straight tongue.: 2" Mounting: 3" x 4" straight tongue Capacity: 7,500 lbs 2-Year limited warranty When you apply the brakes in your tow vehicle, deceleration occurs and momentum pushes your trailer toward
Use this corrosion-resistant actuator to synchronize your trailer brakes with your tow-vehicle brakes. Over-center latch mechanism only engages when the actuator is fully seated on 2" hitch ball. Designed for hydraulic disc brake applications.: 2" Mounting holes positioned 3/4" down Capacity: 7,500 lbs 2-Year limited warranty When you apply the brakes in your tow vehicle, deceleration occurs and momentum pushes your trailer toward
The only option we have for your cab/chassis is the Reese Low Profile 5th Wheel Trailer Hitch, part #RP30054. This hitch has a 30,000-lb gross towing capacity. Installation of this hitch requires it to be installed directly through a 1/2 inch steel…
The LM67000LA is a Timken part number for a bearing cone with a 1.250" I.D. and a 2.328" O.D. This is the same as our bearing part #LM67048. The LM67010 is a Timken part number for a race with a 2.328" O.D. that matches our…
Yes, based on the measurements you took of your hub bore diameter the correct Bearing Buddy Bearing Protectors is the part #BB2441 or #BB2441T-SS for the stainless steel model that will resist any corrosion. These are designed to fit hub bore…
The Dexter 8-201 hub and drums use 12 x 2 inch brake assemblies. You can verify this by measuring your drums as shown in the attached picture. I recommend #AKEBRK-7-SA electric brake assemblies. Both the left and right hand brakes are included and…
The spring with the black cable drum should always be mounted to your LEFT, standing on the inside of the trailer looking out. This is very important for proper operation. Dual spring systems, like #ERS160D96, have a red-coned and a black-coned…
In the USA a tandem axle utility trailer with a gross vehicle weight rating (GVWR) of 7500-lbs should have brakes installed. Any trailer over 3000-lbs must have brakes on all wheels in most states, but laws do vary. Some states require braked axles…
I do have an option for you but all of our trailer wheels with a 5 on 4-3/4" bolt pattern are 15" diameter like the Provider ST205/75R15 Radial Trailer Tire w/ 15" White Spoke Wheel part #A15R475WS. This combo measures 27"…
If you are referring to two white wires from the brake magnet that are coming from the rear of each electric brake assembly, then it would not matter which wire is connected to ground and which wire is used for the brake feed. The magnet that…
Like you said, many factory integrated brake controllers will not work well with electric over hydraulic trailer braking systems. Some of the newer versions of these controllers now have an electric over hydraulic mode. Check to see if any of your…
If your HydraStar Electric Over Hydraulic Actuator #HBA16 isn't pressurizing then I recommend running these 2 tests: 1. Run direct power to the HydraStar by connecting the white wire directly to the negative terminal on a 12V battery and then the…
For a wheel that is 5 inches in width and 15 inches in diameter you would want tires that are size ST205/75-15. For the tire size ST225/75R15 you listed you would want a rim that is from 6-7 inches in width. I attached a department page that has all…
Use this corrosion-resistant actuator to synchronize your trailer brakes with your tow-vehicle brakes. Over-center latch mechanism only engages when the actuator is fully seated on 2" hitch ball. Designed for hydraulic drum brake applications. lockout kit sold separately Made in the USA Specs: Application: hydraulic drum brakes Ball size: 2" Mounting: 3" x 4" straight tongue Capacity: 7,500 lbs 2-Year limited warranty When you
... for hydraulic disc brakes and 3x3 or 3x4 straight tongue. or 3" x 4" straight tongue Capacity: 7,500 lbs 2-Year limited warranty When you apply the brakes in your tow vehicle, deceleration occurs and momentum pushes your trailer toward the rear of your
Use this corrosion-resistant actuator to synchronize your trailer brakes with your tow-vehicle brakes. Over-center latch mechanism only engages when the actuator is fully seated on 2" hitch ball. Designed for hydraulic drum brake applications. lockout kit and fill cap are included Made in the USA Specs: Application: hydraulic drum brakes Ball size: 2" Mounting holes positioned 3/4" down Mounting: straight, 3" wide trailer tongue
... for hydraulic disc brakes and 3x3 or 3x4 straight tongue. is better at reducing corrosion than cast steel master cylinders Raw finish Weld-on installation Made in the USA Specs: Application: hydraulic disc brakes Ball size: 2" Overall length: 17.5"
... for hydraulic disc brakes and 3x3 or 3x4 straight tongue. in the USA Specs: Application: hydraulic disc brakes Ball size: 2" Mounting: 3" x 3" or 3" x 4" straight tongue Capacity: 7,500 lbs 2-Year limited warranty When you apply the brakes
... for hydraulic disc brakes and 3x3 or 3x4 straight tongue. in the USA Specs: Application: hydraulic drum brakes Ball size: 2" Mounting: 3" x 3" or 3" x 4" straight tongue Capacity: 7,500 lbs 2-Year limited warranty When you apply the brakes
... for hydraulic disc brakes and 3x3 or 3x4 straight tongue. in the USA Specs: Application: hydraulic drum brakes Ball size: 2" Mounting: 3" x 3" or 3" x 4" straight tongue Capacity: 7,500 lbs 2-Year limited warranty When you apply the brakes
I like the easy of navigation through the site. It only took me a couple of minutes to place my order. Thank You I will shop this sight again in the future.
Filter Results
