Trailer Idler Hub That Uses a LM67048 Bearing and Has a 5 on 4-1/2 Inch Bolt Pattern
Published 05/14/2018
Products Featured in This Question
Question:
Conner, Thanks. I mis-typed the cap diameter. it should have been 2.328, the same as the cups. I doubt you have any of those either? It seems this old boat trailer is odd in that it has straight spindles and hub bores. At that size they are all tapered spindles now. I may just buy 2 new complete axles.
asked by: Dan
Expert Reply:
The LM67000LA is a Timken part number for a bearing cone with a 1.250" I.D. and a 2.328" O.D. This is the same as our bearing part # LM67048. The LM67010 is a Timken part number for a race with a 2.328" O.D. that matches our part # LM67010. The only trailer hub we have that uses this bearing/race and has a 5 on 4-1/2" bolt pattern is the Trailer Hub Assembly part # DX22XR. This hub uses a LM67048 inner bearing (1.250") and a LM11949 outer bearing (.750").
Unfortunately, we do not have any grease caps with a 2.348" diameter.
Product Page this Question was Asked From
Replacement Trailer Wheel Bearing - LM67048 - Qty 1
- Trailer Bearings Races Seals Caps
- Bearings
- Standard Bearings
- 1.25 Inch I.D.
- Bearing LM67048
- Race LM67010
- 5000 lbs Axle
- 6000 lbs Axle
- etrailer
more information >
Continue Researching
- Shop: Dexter Trailer Idler Hub Assembly for 2,500-lb Axles - 5 on 4-1/2
- Q&A: Replacement Grease Seal For a Trailer Hub Using LM11949 Outer Bearing and LM67048 Inner Bearing
- Search Results: spindle sleeve
- Search Results: sleeves
- Search Results: spindle wear sleeve
- Search Results: wear sleeve
- Search Results: spindle wear sleeves
- Shop: Lippert Spindle Nut Kit w/ D-Flat and Tang Washers - For 2,200-lb to 4,400-lb Axles
- Shop: Lippert Spindle Nut Kit w/ Round Washer - For 2,200-lb to 4,400-lb Axles
- Search Results: 25580 / lm67048 trailer hubs and drums
- Search Results: 125" axle
- Shop: Trailer Axle Beam with Easy Grease Spindles - 95" Long - 3,500 lbs
- Shop: Trailer Axle Beam with Easy Grease Spindles - 86-1/2" Long - 5,200 lbs
- Shop: Trailer Axle Beam with Easy Grease Spindles - 86-1/2" Long - 6,000 lbs
- Q&A: What Is The Smallest Available Spindle Nut For 2.5k Axle?
- Shop: Grease Seal - Single Lip - I.D. 1.500" / O.D. 2.332" for Ag Spindle AS1500E - Qty 1
- Q&A: Recommended 5 Lug Hub for a Spindle w/ 141125 Inner and 09067 Outer Bearings
- Q&A: Replacement Shoreland'r Trailer Hub # 84545UC1-EZ
- Video: All You Need to Know About the Dexter Trailer Idler Hub Assembly for 2,500-lb Axles
- Q&A: Trailer Idler Hub That Has a 5 on 4-1/2 Lug Pattern and Uses LM67048 and LM11949 Bearings
- Video: What to Know About the DeeMaxx Drive-In Wheel Stud
- Video: Replacement Shackle Strap Feature Review
- Video: Talking Pre-Greased Trailer Hub and Drum Assemblies with TruRyde
- Q&A: How to Determine What the Correct Replacement Hub Is
- Q&A: 4 Bolt Hub and Spindle Nut for a CE Smith 2k Trailer Axle
- Video: An In-Depth Look at the Curt 7-Way Trailer Plug Extension
- Video: Ultimate Overview of the Curt 7-Way Trailer Plug Extension
- Shop: Trailer Wiring
- Video: CE Smith Trailer Idler Hub Assembly w/ Case for 2.5K Axles Spec Review
- Shop: Fifth Wheel Hitch
Dan
5/14/2018
Conner, Thanks. I mis-typed the cap diameter. it should have been 2.328, the same as the cups. I doubt you have any of those either? It seems this old boat trailer is odd in that it has straight spindles and hub bores. At that size they are all tapered spindles now. I may just buy 2 new complete axles.