8-1/4" x 3-1/4". Incandescent marker light mounts on your trailer fender. Built-in reflex reflector. Amber light faces front, and red light faces rear. Surface mount to trailer with bracket. Pre-wired design. (2) 194 bulbs.
8-1/4" x 3-1/4". Incandescent marker light mounts on your trailer fender. Built-in reflex reflector. Amber light faces front, and red light faces rear. Surface mount to trailer with bracket. Pre-wired design. (2) 194 bulbs.
5" x 4-1/2" Square. Waterproof trailer light serves 6 functions: stop, turn, tail, rear reflex, side marker, and side reflex. SMD LEDs for enhanced performance. Stud mount on 2" centers. 3-Wire design.
To create barn doors out of your ramp door, you will need hinges and a latch. I suggest a latch/lock system like the Universal Cam-Door Lock for Enclosed Trailers - 1" Keeper, #383200. This will use a 3/4 inch diameter pipe that…
I can help you pick out the correct hub, but we don't have a cross-reference part number for the one you listed. In order to pick out the correct hub assembly for a trailer you are going to need know a few key pieces of information. The…
The UFP H-1377 correlates to a Dexter #84 spindle, which is for a 3,500 pound axle. This will utilize an inner bearing #L68149 and an outer bearing #L44649. As this is being used on a boat trailer, I highly suggest going with the etrailer.com…
The Bearing Buddy Bearing Protectors like part #BB1781 will only work for standard spindles, not those with grease fittings in the end which are also known as EZ-Lube. They both are designed to provide easy lubrication to the bearings without…
I have attached a photo of what I believe you have on your John Deere Tractor. If that is the case then this is what is referred to as a 7-pole trailer wiring harness and in order to then adapt this for use with a 7-blade trailer connector you would…
Swapping the mounting hardware on a jack can be done, but it will depend on the specific mounting hardware of the jacks. Shelby jacks and parts are becoming more difficult to locate, so I would recommend replacing your Shelby hardware with something…
The Draw-Tite Max-Frame Trailer Hitch Receiver #75282 will have the following bolt hole dimensions for your 2015 Nissan Frontier. The Bolt holes from drivers side to passenger side frame rails are 43-5/8" on center. The holes running from front…
The fuse for the trailer running lights on your 2005 GMC Sierra 1500 is going to be located in the engine bay fuse box and will be labeled as the trailer parking lights. If you just visually inspected the fuse it may have been missed because not all…
The Dexter Electric Trailer Brake Assembly #K23-532-00 has a square mounting pattern with the bolt holes centers being 3-3/4" on center. This particular assembly is for the drivers side of the 8,000-lb AL-KO / Hayes axle. We also have the…
Testing the brake controller is fairly easy. Sever the blue brake output wire near the brake controller leaving enough room to reconnect it and then apply the manual slide. Using a circuit tester like part #PTW2993, you should get output to the…
There are a couple of reasons why your Primus IQ trailer brake controller #TK90160 could be flashing. It could be a bad ground connection, an overload or the angle of the controller not accurate for use. The angle is an issue because it utilizes an…
4-1/2" x 5" Square. Waterproof trailer light serves 6 functions: stop, turn, tail, rear reflex, side marker, side reflex, and license plate light. SMD LEDs for enhanced performance. Stud mount on 2" centers. 3-Wire design.
3-3/4" Round. Incandescent trailer light serves as a stop, tail, and turn signal light. Durable polycarbonate housing with screw-on lens. Stud mount with included studs. 2-Wire design grounds through mounting hardware. (1) 1157 Bulb.
3-1/2" x 1-1/8" Oval. Low-profile incandescent trailer light serves as a clearance or side marker light. Durable base with scratch-resistant acrylic lens. Surface mount - horizontal or vertical. 1-Wire design. P2 rated. (1) 194 bulb.
2-1/8" x 1-1/8" Rectangle. Waterproof, LED trailer light serves as either a side marker light or clearance light when properly mounted. Durable polycarbonate lens and housing. Stud mount to trailer. Single wire design. P2 rated.
3/4" Diameter round. Waterproof, LED trailer light functions as both a clearance and side marker light when properly mounted. Durable polycarbonate base and lens. Recessed mount with included grommet. 2-Wire pigtail. PC rated.
I like the easy of navigation through the site. It only took me a couple of minutes to place my order. Thank You I will shop this sight again in the future.
Filter Results
