How to Install/Remove Snap Ring From Fulton Jack # FTJ120W0301

Question

Question:

How do I make the snap ring fit the jack. It doesnt want too

asked by: Paula B

0

Expert Reply:

To remove the snap ring from the Fulton Swivel Jack part # FTJ120W0301, you will need snap-ring or retaining ring pliers. These pliers are available at most local hardware and auto parts stores.

The snap ring pliers will have two pins on the end that will fit in the holes of the snap ring on jack. When you squeeze the pliers, the ring will open up enough to be removed.

To replace the snap-ring, you will simply use the snap ring pliers to open the ring enough to fit it back into place.

expert reply by: Jameson C

0

Answer 1

Jack #DL22210 isn't a snap ring jack but we do have other options that will likely work with your existing mount such as #FTJ120W0301. The hole spacing for the pull pin is 3 inches apart on center. I have linked a video review of this jack for…

view full answer...

Answer 2

Hi Rick, For a Fulton weld-on trailer jack that has a snap ring you can use the Fulton Boat Trailer Jack w/ Wheel - Sidewind - Swivel - 10" Lift #FTJ120W0301. I've added a link below to a video review of this jack as well if you'd like…

view full answer...

Answer 3

They make snap ring pliers that are used to remove snap rings. It has two pins on the end that stick into the holes of the snap ring and when squeezed it will open up the ring enough to be removed. You might also try to use 2 regular pliers. With one…

view full answer...

Answer 4

In order to remove a welded-on trailer tongue jack you will need to cut off the old welds to release the mounting bracket. This can be done using an angle grinder. The jack can then be replaced with another welded-on option such as the Fulton Marine…

view full answer...

Answer 5

Based on my research, the Fulton Round, Snap-Ring Swivel Marine Jack #FTJ120W0301 will be a perfect replacement for your Shelby 5756A trailer jack. This jack will allow you to use the existing snap ring jack mount on your trailer for installation.…

view full answer...

Answer 6

According to our research the Fulton Round, Snap-Ring Swivel Marine Jack #FTJ120W0301 will fit as a replacement for your Shelby 5756 boat trailer jack. It will allow you to keep the same bracket that is currently welded-on. You basically need to open…

view full answer...

Answer 7

The correct replacement for the Fulton Magnum Series Trailer Jack on your trailer is the Fulton Bolt-Thru Swivel Marine Jack part #FXP10W0301 if you have a bolt-thru mounting bracket or part #FTJ120W0301 if you have a snap-ring mounting bracket. I…

view full answer...

Answer 8

I have an option for you, but since Shelby is out of business you will not be able to purchase another Model 5856A jack. Instead I recommend replacing it with the Fulton Round, Snap-Ring Swivel Marine Jack - Weld On - Sidewind - 10" Lift - 1,200…

view full answer...

Answer 9

Although we don't offer a direct replacement, as Shelby is no longer in business, the Fulton #FTJ120W0301 would be compatible with the snap ring base your Shelby 5776 used. The jack has a 1200 lb capacity and offers 10 inches of lift. I'll…

view full answer...

Answer 10

What we have heard from our customers is that the Fulton #FTJ120W0301 does fit the mounting plate of the Shelby Jack 5784. This would be your best option for a direct replacement.

view full answer...

Answer 11

We did have a customer come back and say that the Fulton jack part #FTJ120W0301 will attach just fine to the pipe mount on the trailer frame where a Shelby jack just like yours was installed.

view full answer...

Answer 12

I have a solution for you, but we do not carry an adapter like you mentioned to mount a square tube jack to your existing winch stand. The best option for your set-up may be to use a jack like the Pro Series Square Jack with Footplate #PS1400850383.…

view full answer...

How to Install/Remove Snap Ring From Fulton Jack # FTJ120W0301

Product Page this Question was Asked From

Continue Researching