Weld-On Fulton Trailer Jack That Uses a Snap Ring

Question

Question:

I have a 2001 glastron trailer with a Fulton Jack which seems to be seized. It is welded on, but I see a snap ring that would remove it. What Jack would I need to replace it on the swivel with a snap ring?

asked by: Rick S

0

Expert Reply:

Hi Rick,

For a Fulton weld-on trailer jack that has a snap ring you can use the Fulton Boat Trailer Jack w/ Wheel - Sidewind - Swivel - 10" Lift # FTJ120W0301.

I've added a link below to a video review of this jack as well if you'd like to check it out.

expert reply by: Kyle S

0

Rick

10/1/2024

Thanks Kyle! I’m ordering it now.

Answer 1

To remove the snap ring from the Fulton Swivel Jack part #FTJ120W0301, you will need snap-ring or retaining ring pliers. These pliers are available at most local hardware and auto parts stores. The snap ring pliers will have two pins on the end that…

view full answer...

Answer 2

Jack #DL22210 isn't a snap ring jack but we do have other options that will likely work with your existing mount such as #FTJ120W0301. The hole spacing for the pull pin is 3 inches apart on center. I have linked a video review of this jack for…

view full answer...

Answer 3

The only trailer jack that will work with your existing mounting bracket and not contact the boat with a full rotation of the handle is the Fulton Bolt-Thru Swivel Marine Jack part #F1411300301. I understand this does not have the sharkskin coating…

view full answer...

Answer 4

The ARK trailer jack part #ARK57FR uses a dual wheel setup with rubber tires that were designed for getting over off-road terrain which will be much easier to move by hand but the easiest would be the Trailer Valet 5X part #STC-V211 which comes with…

view full answer...

Answer 5

In order to find which snap ring you need you would have to measure the outer diameter of the snap ring bracket on your trailer frame. A part like the #DL22672 REPL Snap Ring for Swivel Trailer Jacks - 2-5/16" Inner Diameter will fit trailer…

view full answer...

Answer 6

Yes, the Fulton XLT Bolt-Thru Swivel Trailer Jack #F141132 that you referenced is designed to fit the same style of mounting bracket that you have in the picture you submitted. This jack will bolt right up.

view full answer...

Answer 7

The Fulton jack part #F141132 that you referenced is a really great jack that I know you'll be happy with, but it requires the bracket part #P9012-00 to mount to a trailer which isn't the same as what you have now. So your best option is to…

view full answer...

Answer 8

Yes, we have replacement snap rings for Dutton Lainson jacks like the #DL22560 that you referenced with the part #DL22672.

view full answer...

Answer 9

For your particular application, going with a single 8 inch wheel like what is on the Fulton XLT Bolt-Thru Swivel Trailer Jack #F141133 is going to be the better option. A dual wheel jack can be more beneficial on surfaces other than pavement, as a…

view full answer...

Answer 10

I am happy to point you in the right direction. According to the online owners manual for a 2004 Ranger Trailer CF5000 Z20 boat trailer, it uses a 1200 lb Fulton Swing Jack. They do not mention any other specs, but from what I can see, they use a…

view full answer...

Answer 11

Thank you for providing the picture of your existing mount. This was helpful to idenfication and I have attached it to this post. As you mentioned, the 90 degree snap in holes are 3" apart from center to center. It may be helpful to note that…

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Weld-On Fulton Trailer Jack That Uses a Snap Ring

Featured Help Information

Miscellaneous Media

Continue Researching