Replacement for Haulmark # 900200 Fender Marker Light on 10 x 5 Enclosed Trailer

Question

Question:

2011 Haulmark 10x5 covered trailer model #TST5X10DS2 # on light is A-V 1260 AV haulmark # 900200 Will this light work on it? Just need the light. Recepicol it plugs into we have.

asked by: Connie B

1

Helpful Expert Reply:

Although I don't have any reference information that would tell me the part or crossover number for a lamp on your Haulmark trailer, I found online that the # MC65ARB you referenced would be an identical replacement. To be sure, take a quick measurement of the existing lamp on the other side. If it measures 3-15/16 inches long by 1-1/4 inches wide by 7/8 of an inch tall when laid on the base, you're good to go. You might consider getting the # A65PB, # A67CB or the # A67BB base, they're inexpensive and this way you'll be absolutely sure you have a matching lamp and base.

expert reply by: Mike L

1

Answer 1

Hey Ben, thanks for reaching out. The Replacement Universal Axle Bracket for Firestone Ride-Rite Air Springs #F22VV is a single bracket. We sell them individually.

view full answer...

Answer 2

The Fulton T1401 model has been discontinued. As a replacement I recommend the Fulton Single Speed Trailer Winch - 8" Long Handle - 1,500 lbs #F142201. The slightly smaller option is the Fulton Single Speed Winch - 8" Long Handle - 1,300…

view full answer...

Answer 3

A 16 inch tire will not fit on a 16.5 inch wheel. You would either need to get new 16 inch wheels with the proper bolt pattern to match what the hubs require or to get your existing wheels you would need to go with 16.5 inch tires. You mentioned you…

view full answer...

Answer 4

To replace your Atwood RV Water Heater, Model #GC10A-4E, the direct replacement is the Atwood RV Water Heater - Gas and Electric - part #AT94022. This is the new version of your existing water heater, so it will have all the same features like a…

view full answer...

Answer 5

From what I have found, the ALKO hub and drum assembly you have is for 7,000 lb axles. I believe the Dexter Trailer Hub and Drum Assembly for 5,200-lb to 7,000-lb Axles - 12" - 8 on 6-1/2 #8-219-4UC3 will work as a replacement. This has the same…

view full answer...

Answer 6

If you are looking for the center section of the bracket that is in the picture you submitted of the #MCL67ARB that you referenced the correct part number you need is the #A65P that you referenced.

view full answer...

Answer 7

In order to find a replacement side marker light for your 2015 Dynamax Dynaquest I recommend taking some measurements of the current light. There is not a direct replacement available so you will need to find something that is a close match and…

view full answer...

Answer 8

It's normal for some clearance lights to ground through the mounting screw instead of running an extra wire so there's nothing wrong with that. For the amber clearance lights you can use part #MCL67AB and for the red part #MCL67RB. These both…

view full answer...

Answer 9

There are five mounting brackets available that fit the Optronics Trailer Clearance Side Marker Light #MC65AB. These three are all black plastic. They are Optronics #A65PBPG, #A65PB and #A65B. The first two come with a single wire, the…

view full answer...

Answer 10

Hi David; based on what we have found in the past your TDE 46845 uses #L68419 inner and #L44649 outer bearings. There should only be the one grease seal like a standard hub, which as far as we know is the #168255TB with an inner diameter of…

view full answer...

Answer 11

There is an easier solution that a different jack. You can use a longer ball mount so that the trailer, and the jack, will be further away allowing you to lower the tail gate without hitting the jack. Then you could use any jack you wanted. If that…

view full answer...

Replacement for Haulmark # 900200 Fender Marker Light on 10 x 5 Enclosed Trailer

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching