How Tight Should the Lug Nuts of the Trailer Hub Assembly # 8-258-5UC1 be Tightened

Question

Question:

lug nut torque spec for Trailer Hub Assembly for 13inch to 15inch Wheels - 2,200-lb Axles - 5 on 4-1/2 - L44649 Bearings

asked by: Charles N

0

Expert Reply:

The torque rating that should be used to tighten lug nuts to the Trailer Hub Assembly # 8-258-5UC1 that you referenced would be between 75 and 85 ft lbs.

expert reply by: Jameson C

0

Answer 1

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 2

From the information that I was able to find on the L44549 bearing, it shows it being a 1-1/16 inch bearing which is the same as Trailer Hub Bearing, #L44649. Just to be sure, I recommend measuring the L44549 bearing with a digital caliper to confirm…

view full answer...

Answer 3

For a Dexter hub 8-258 the correct seal is the part #10-9.

view full answer...

Answer 4

The Dexter Hub part #8-258-5UC1-EZ is an exact match for the hubs you have on your trailer currently and would be a great choice. Bearing Buddies can be pretty convenient but the problem with them is that they make it too easy to over fill the hub…

view full answer...

Answer 5

Verify your bearing numbers and bolt pattern to be sure but I believe either #8-258-5UC1-EZ for E-Z Lube axles or #8-258-5UC1 for standard axles is what you need. Both of these hubs include bearing #L44649 for the inner and outer. They have a 5 on…

view full answer...

Answer 6

The hub you have is the part #8-259-5UC1 which is what you'd need for a replacement. This comes with all of the needed bearings, seals, and cap as well.

view full answer...

Answer 7

We do have a couple of alterative solutions, however we do not carry a replacement that match those dimensions. Instead, I recommend replacing the entire swing down stabilizer with the Stabilizer Jacks #TJ01RT-HD which measures 18" extended,…

view full answer...

Answer 8

Hey Monty, When installing hubs on an axle they should turn freely. Initially you will feel slight resistance but once the seals set it should be able to turn freely. Some things that may cause resistance could be a damage or improperly pressed…

view full answer...

Answer 9

Moving the wheel could help allow the grease to make its way into the hub of your trailer, but it could also be a clogged zerk fitting. There isn't an easy way to unclog zerk fittings so you may just need to replace the Bearing Buddys with the…

view full answer...

Answer 10

The piston could certainly be bad, or perhaps even the zerk fitting. Try removing the bearing buddy and applying grease while it is off of the hub. I had the same thing happen on my jet ski trailer, I replaced the bearing buddy which fixed the…

view full answer...

Answer 11

You will want our Bearing Kit #BK1-150 for your boat trailer. It includes both inner and outer races and bearings, a new grease seal, a cotter pin and tang washer.

view full answer...

Answer 12

Based on the pictures you attached and the outer bearing measurement you provided, it appears that you have 1-1/16 inch spindle like the BTR EZ Lube Spindle #TRU44FR. This particular spindle is designed for 2,000 pound axles and will use the same…

view full answer...

How Tight Should the Lug Nuts of the Trailer Hub Assembly # 8-258-5UC1 be Tightened

Product Page this Question was Asked From

Continue Researching