Where to Drill the 4 inch Hole in the Truck Bed of 2015 Ford F350 to install BW Turnover Gooseneck
Published 09/25/2014
Question:
The instructions for the installation say to center your hole at 46-1/8inch but the center of the recess in the bed and center punch mark that is factory made Into the bed is around 45-3/4. If I install at 46-1/8inch the ball with not be even close to centered up in the recessed location. But of course I do not want to install at the wrong location. You only get one shot when it comes to drilling the 4inch hole.
asked by: Chad
Expert Reply:
The ball hole location set out in the instructions for the B&W Turnoverball Underbed Gooseneck Trailer Hitch # BWGNRK1111 was made with the installation brackets and hardware of the # BWGNRK1111 in mind. The hole may not be perfectly in the recessed portion of your truck bed, but it will match up with the hitch once installed.
If you drill the hole where you think it would be in relation to the recessed portion of the bed it won't line up with the gooseneck ball once the hitch has been installed.
As always, measure twice and cut once.
I attached an install video for you to check out as well.
Product Page this Question was Asked From
B&W Turnoverball Underbed Gooseneck Trailer Hitch w/ Custom Installation Kit - 30,000 lbs
- Gooseneck Hitch
- Below the Bed
- Flip-Over Ball
- 7500 lbs TW
- 30000 lbs GTW
- Wheel Well Release
- Spring-Loaded Loop
- B and W
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Search Results: tongue box
- Shop: etrailer Trailer Tool Box - A-Frame - Aluminum - 3.4 Cu Ft - 34" Long - Matte Black
- Shop: Trailer Wiring
- Video: Gooseneck Trailer Hitch Installation - 2014 Ford F-250 Super Duty
- Q&A: Hole for B&W Turnoverball Doesnt Line Up With Dimple On a 2019 Ford F-250
- Shop: Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Shop: Aluminum AM01 Series Black Machined Trailer Wheel - 12" x 4-1/2" Rim - 5 on 4-1/2
- Shop: Aluminum AM02 Series Black Machined Trailer Wheel - 12" x 4-1/2" Rim - 5 on 4-1/2
- Shop: Aluminum AM02 Series Gunmetal Machined Trailer Wheel - 12" x 4" Rim - 5 on 4-1/2
- Shop: Replacement Orifice Connector for Dexter Actuators
- Shop: B&W Turnoverball Underbed Gooseneck Trailer Hitch w/ Custom Installation Kit - 30,000 lbs
- Shop: Gooseneck Hitch
- Shop: Trailer Hitch
- Search Results: gooseneck hitch
- Article: Trailer Wiring Diagrams
- Search Results: trailer hitch
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Search Results: trailer tires and wheels
- Video: Measuring To Choose The Right Trailer Axle
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: Comparing Kenda KR03, KR35, And KR53 Tires
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Search Results: trailer wiring
- Shop: Suspension Enhancement
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Article: How to Measure for Trailer Hitch Drop
- Search Results: trailer jack
- Shop: Brake Controller
- Video: Curt T-Connector Vehicle Wiring Harness Review C56040
on Gooseneck Hitch
