When you’re hauling gear or towing heavy, this wheel’s 1,520-lb load rating keeps your setup solid. The 12" x 4" aluminum rim meets DOT specs and uses steel inserts in the lug wells to hold torque under pressure. It stays tight on the hub and eliminates the need for constant retightening after long runs.
Salt spray and humidity can ruin a steel wheel, but not this one. The gunmetal aluminum build is rustproof, with a clear coat on both sides that shields against scratches and corrosion. The split-spoke design looks sharp and stays that way, season after season.
Over time, plain aluminum holes can wear down from repeated torque cycles. This wheel solves that with steel inserts in each lug nut well, keeping the wheel secure and helping prevent elongation around the bolts. It’s a small feature with big payoff in reliability.
The wheel uses a standard 5 on 4-1/2" bolt pattern with a 3.19" pilot hole and 0 offset for straightforward mounting. Bolt size is 1/2"-20, so matching up hardware is simple when you’re putting everything together.
This machined aluminum design looks good but it’s built for work too. Lightweight construction helps reduce strain on bearings while still giving you strong support for heavier loads. It’s practical performance with an upgraded look that fits right in on any trailer project.
1. Count the lug holes
Look at the wheel hub or the back of the wheel and count how many lug holes there are(also called bolt holes).
Common configurations include: 4-lug, 5-lug, 6-lug and 8 lug
2a. For even lug counts (4-lug, 6-lug, 8-lug)
Measure from the center of one lug hole directly across to the center of the hole opposite it.
Common configurations: 4 on 4", 6 on 5.5", 8 on 6.5"
2b. For odd lug counts (5-lug)
Measure from the center of one lug hole to the outer edge of the hole directly across (not center-to-center since there's no directly opposite hole).
Common configurations: 5 on 4.5" (most popular), 5 on 5", 5 on 4.75", 5 on 5.5"
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Hello everybody, this is Jeff at etrailer.com. Today, we're gonna take a look at the Americana 12 inch by 6 inch gunmetal gray machined AM02 series aluminum trailer wheel with the 5 on 4-1/2 half inch bolt pattern. Now, this is an aluminum wheel. It is durable, lightweight, and rust-proof. It is the Americana AM02 series, which you can see is a split five-spoke design, has a gunmetal gray finish with the machine finish on the face of the spokes and even on the lip. Now, the front and even the back of the wheel are clear coated to protect against scuffs and scratches.
Now, they do use steel inserts. That's one of the best features I like on this wheel is the steel inserts that are pressed into the lug nut wells. They're designed to help keep your wheel securely in place on the trailer hub. Basically, when you put this on your hub, your studs will come through here. You'll put your lug nets in and torque them down, and those inserts prevent the holes from elongating or wearing down over time, so it eliminates the need for constant re-tightening of your lug nuts.
This is a high-quality wheel. It does meet the DOT Department of Transportation specifications. A few dimensions on this, the diameter we're gonna measure, which is always measured inside to inside, and then we're also gonna measure the width. So if we first do the diameter inside to inside, there's your 12 inch measurement. The width, same way, we're gonna measure inside to inside or bead seat to bead seat, there's your four inch width.
Now, this wheel does have a bolt pattern of 5 on 4-1/2 inches. And if you wanna measure that on a wheel that's an odd number of lugs, in this case five, what you need to do is pick any hole, let's say this one, and then you're gonna have to measure across to either one of these holes. But the trick is you measure from the center of the starting hole to the furthest edge of the hole that you measure to. So on this one, it'll measure 4-1/2 inches. So this is a 5-lug 4-1/2 inch bolt pattern.
Does use a wheel lug size of 1/2 inch by 20. Now the pilot hole, which is this large hole here in the center, the diameter on that opening is 3.19 inches. And the last thing on this, the load rating or weight capacity on this wheel is 1,520 pounds. But that should do it for a look at the Americana 12 inch by 4 inch gunmetal gray machined AM02 series aluminum trailer wheel.
Customer Satisfaction Score:
88% were satisfied with this product
12% of customers were not satisfied
Ratings & Reviews
Thank you so much for a great product and super fast shipping.
Really good rims
Fit great, look amazing. Way better than the typical steel or galvanized you normally get
This was the wheel I wanted and etrailer is the only company that had them. Quick shipping and delivery - could not have been better - unless they were given to me.
Info for this part was:
At etrailer we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.