Availability of a Stabilizer Jack for a 2014 Jayco Pop Up Trailer

Question

Question:

Im looking for a domar jack that is used on my 2014 Jay-co pop up trailer. It isnt exactly a scissor jack, more like half of a scissor jack made by Domar and says PJ-01. Do you sell this particular stabilizer jack. Im trying to replace one that bent to match the other.

asked by: Greg L

0

Expert Reply:

We do carry the Domar stabilizer jack # TJ01RT which has a capacity of 650 pounds.

I have attached a couple videos too.

expert reply by: Chris B

0

Answer 1

I do have a recommendation for you as we do not carry the PJ-01 stabilizers. Instead you might consider replacing your stabilizers with the much stronger Ark Drop Down Corner RV Stabilizer Jacks #AR34FR. This will include 2 jacks which are much more…

view full answer...

Answer 2

For a replacement jack for your 2021 Jayco Jay Flight SLX 7 174 BH I recommend the Stabilizer Jack - 6-1/4" Drop Leg Travel - 18" - 650 lbs #TJ01RT. This jack same mounting hole dimensions as your current jack at 3 inches apart on center.…

view full answer...

Answer 3

Hey Hannah, thanks for reaching out. Yes, the Curt #C59236 will indeed work on a 2026 Chevy Equinox EV LT1 without the tow package. This is a universal hardwire harness that can be used on most vehicles. There are no custom plug-in harnesses for the…

view full answer...

Answer 4

Hello Matthew, thanks for reaching out. I can provide dimensions of the Timbren Axle-Less Trailer Suspension #A20RS545, but we do not have any 3D drawing we can share. Only the manufacturer would have access to stuff like that, and typically they…

view full answer...

Answer 5

We do offer E-Track Trailer Cargo Control that will work on the floor of a trailer and also will work on the wall of an enclosed trailer. For the vertical E-Track channels typically used for walls you can order part #E19146. These are sold…

view full answer...

Answer 6

The MORryde Scissor Jack Cross Brace Stabilizer #MR82AR is the only version available. Since your scissor jacks aren't mounted at a 90 degree angle this will not work for your 2024 Grand Design Momentum 31G. For additional stabilization I…

view full answer...

Answer 7

Hey Andersen, without any type of attachment installed on the Power Mountain TallBoy Off Road Bottle Jack part #PM34FR the height is 9 inches when fully retracted and then 15 when extended. The lift range is right around 6-1/2 inches. Would that work…

view full answer...

Answer 8

Since there isn't a latch on top of the ball of the #BWGNXA2061 you can use it with a fifth wheel to gooseneck adapter like the Andersen Ranch Hitch #AM3100 that you referenced. The other similar options that have the release lever on top of the…

view full answer...

Answer 9

To replace your AL-KO 568303 seal you will want the Oil Seal #91030. This seal has the same inner diameter of 2.750 inches and outer diameter of 3.779 inches. It is a confirmed fit for your #99 spindle that uses the AL-KO 568303 seal.

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

Hey Jeff. There is definitely a correlation between weight and capacity. I've listed the weight of all three of the Power Mountain Tallboy Off-Road Bottle Jacks we have below: Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...