Recommended Voyager WiSight Camera for a New Trailer Without Pre-Wire

Question

Question:

Hi, would you know where I can get the pre-wired plate that RVs come with for the Voyager WySight 2.0 camera? I changed Rvs and want to mount my Voyager to the new one. Thanks

asked by: Bob C

0

Expert Reply:

Bob, as far as I know that is something that had to have been installed at the manufacturer, so it's not offered separately. You can still install the rest of your Voyager WiSight camera system on your new trailer, you're just going to need the new camera # ASA64YR and you'll then need to wire it to either your reverse lights or running lights depending on what you're wanting.

The monitor and the 12v outlet wiring both work with the new camera so you shouldn't need anything else.

expert reply by: Bryce D

0

Thanks

5/24/2024

Thanks. Rather than buy a new camera, I'm going to install the Wisight one, and use the connector and adapter kit cable I just ordered from you. I should be able to stuff it in the existing hole, it appears deep enough tho push the wisighjt camera's connector and cable thru. Thanks again, Bob

Bryce D.

5/24/2024

@Thanks Okay, sounds good let us know how it works for you!

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 6

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 9

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 10

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Answer 11

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 12

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Recommended Voyager WiSight Camera for a New Trailer Without Pre-Wire

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching